720835

Stanley STHT0-77364 Manual

7
Zoom out
Zoom in
Previous page
1/208
Next page
7
terminal if the current to be measured is
less than 200 mA. If the current is between
200 mA and 10 A, connect the red test lead
to the 10 A terminal instead.
2. Set the range switch to desired range
position. Note: If the magnitude of the current
to be measured is not known beforehand,
set the range switch to the highest range rst
and then reduce it one range at a time until
the appropriate resolution is obtained.
3. Turn off power to the circuit to be tested.
Then discharge all capacitors.
4. Break the circuit path to be tested, and
connect the test leads in series with the
circuit.
5. Turn on power to the circuit.
6. Read the reading on the display. The polarity
of the red test lead connection will be
indicated.
WARNING: To avoid risk of personal
injury and/or possible damage to the meter,
when using the 10 A terminal, you should only
acquire readings for 10 seconds maximum with
a minimum resting time of 15 minutes between
readings.
WARNING: To avoid electric shock or
damage to the meter, do not apply terminals to
amperage higher than 200 mA when connected
to the terminal. Do not apply terminals to
amperage higher than 10 A when connected to
the 10 A terminal.
MeasuringResistance
1. Connect the black test lead to the COM
terminal and the red test lead to the
terminal.
2. Set the range switch to desired range
position.
3. Connect the test leads across the object to
be measured.
4. Read the reading on the display.
Note:
1. For measurements >1000 kΩ, the meter
may take a few seconds to stabilize the
reading. This is normal for high resistance
measurements.
2. When the input is not connected, i.e. at open
circuit, “1” will be displayed as an overrange
indication.
WARNING: To avoid electric shock or
damage to the meter, before measuring in-
circuit resistance, disconnect all power to the
circuit to be tested and discharge all capacitors
thoroughly.
ContinuityTest
1. Connect the black test lead to the COM
terminal and the red test lead to the
terminal.
2. Set the range switch to the position.
3. Connect the test leads across the object to
be tested.
4. If the resistance is lower than approximately
30 Ω, the built-in buzzer will sound.
WARNING: To avoid electric shock or
damage to the meter, before performing
continuity test, disconnect all power to the
circuit to be tested and discharge all capacitors
thoroughly.
DiodeTest
1. Connect the black test lead to the COM
terminal and the red test lead to the
terminal. Note the polarity of the red test lead
is positive (+).
2. Set the range switch to the position.
3. Connect the red test lead to the anode of the
diode to be tested and the black test lead to
the cathode of the diode.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHT0-77364 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHT0-77364 in the language / languages: All languages as an attachment in your email.

The manual is 29,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info