720835

Stanley STHT0-77364 Manual

6
Zoom out
Zoom in
Previous page
1/208
Next page
6
User Manual
GB
but the measurement error may be large or the
thermocouple may be damaged.
Note:
1. Use K Type thermocouple.
2. Accuracy does not include error of the
thermocouple probe.
3. Accuracy specication assumes ambient
temperature is stable to ±1°C. For ambient
temperature changes of °C, rated accuracy
applies after 1 hour.
4. There is no stated accuracy for the
thermocouple provided with this unit.
Readings with this thermocouple should be
used for reference only.
OPERATING INSTRUCTIONS
BATTERY
Remove battery door Phillips head screw, open
the battery door and connect a 9 V battery to
the clip. Put battery into case, close battery
cover and replace screw. When the low
battery indicator
appears on the display,
the battery is low and must be replaced
immediately.
USAGE
DataHoldFeature
Press the HOLD button to enable the Data
Hold feature. The current reading will be held
on the display. To disable, press HOLD again.
Note: If the display does not turn on or the
reading on display does not change, the HOLD
button may be depressed. Try disabling the
Data Hold feature.
MeasuringDCVoltage
1. Connect the black test lead to the COM
terminal and the red test lead to the
terminal.
2. Set the range switch to desired
range
position. If the magnitude of the voltage to be
measured is not known beforehand, set the
range switch to the highest range rst and
then reduce it one range at a time until the
appropriate resolution is obtained.
3. Connect the test leads across the source or
circuit to be tested.
4. Read the reading on the display. The polarity
of the test lead connection will be indicated.
WARNING: To avoid electric shock or
damage to the meter, do not apply terminals to
voltage higher than 300 V.
MeasuringACVoltage
1. Connect the black test lead to the COM
terminal and the red test lead to the
terminal.
2. Set the range switch to desired range
position. If the magnitude of the voltage to be
measured is not known beforehand, set the
range switch to the highest range rst and
then reduce it until satisfactory resolution is
obtained.
3. Connect the test leads across the source or
circuit to be tested.
4. Read the reading on the display. If the
magnitude of the voltage to be measured is
not known beforehand, set the range switch
to the highest range rst and then reduce it
range by range until satisfactory resolution is
obtained.
5. Read the reading on the display.
WARNING: To avoid electric shock or
damage to the meter, do not apply terminals to
voltage higher than 300 V.
MeasuringDCCurrent
1. Connect the black test lead to the COM
terminal and the red test lead to the
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHT0-77364 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHT0-77364 in the language / languages: All languages as an attachment in your email.

The manual is 29,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info