720462
7
Zoom out
Zoom in
Previous page
1/11
Next page
7
ENGLISH
(Original instructions)
Keyed chuck (fig. D)
Open the chuck by turning the sleeve (12)
anti-clockwise.
Insert the bit shaft (13) into the chuck.
Insert the chuck key (14) into each hole (15) in the side
of the chuck and turn clockwise until tight.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check
for the location of wiring and pipes.
Warning! Do not apply chisels when the tool is in the drilling
mode.
Selecting the operating mode (fig. F)
The tool can be used in three operating modes.
To operate the drilling mode selector (3), rotate it
towards the required position, as indicated by the
symbols.
To operate the operating mode selector (4), push the
unlock button (16) and rotate the selector towards the
required position, as indicated by the symbols.
Drilling
For drilling in steel, wood and plastics, and for
screwdriving set the operating mode selector (4) to the
position and the drilling mode selector (3) to the
position.
Hammer drilling
For hammer drilling in masonry and concrete, set the
operating mode selector (4) to the position and the
drilling mode selector (3) to the position. When
hammering, the tool should not bounce and run
smoothly. If necessary, increase the speed.
Hammering
For hammering with spindle lock, and for light chiselling
and chipping, set the operating mode selector (4) to the
position and the drilling mode selector (3) to the
position.
When changing from hammer drilling to chiselling, turn
the chisel to the desired position. If resistance is felt
during mode change, slightly turn the chisel to engage
the spindle lock.
Switching on and off
Select the required speed by turning the speed selector
dial (2).
To switch the tool on, press the on/off switch (1).
To switch the tool off, release the on/off switch.
Brush monitor (fig. E)
Your tool has a built in system that monitors the health of the
brushes.
Green brush monitor indicator (17). The brushes are in
good condition.
Red brush monitor indicator (18). The brushes are warn
and need replacing, return your tool to an authorised
STANLEY Service Centre in order to to have the brushes
replaced.
Accessories
The performance of your tool depends on the accessory
used. STANLEY and Piranha accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you
will get the very best from your tool.
Maintenance
Your Black & Decker corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on
corded/cordless power tools:
Switch off and unplug the appliance/tool.
Regularly clean the ventilation slots in your
appliance/tool/charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHR323 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHR323 in the language / languages: English as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info