720462
6
Zoom out
Zoom in
Previous page
1/11
Next page
6
ENGLISH
(Original instructions)
Residual risks.
Additional residual risks may arise when using the tool
which may not be included in the enclosed safety warnings.
These risks can arise from misuse, prolonged use etc. Even
with the application of the relevant safety regulations and
the implementation of safety devices, certain residual risks
can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
Injuries caused when changing any parts, blades or
accessories.
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by
the manufacturer or an authorised STANLEY Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/Off switch
2. Speed selector dial
3. Drilling mode selector
4. Operating mode selector
5. Tool holder
6. Side handle
7. Depth stop
8. Grease cap
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle (fig. A)
Turn the grip counterclockwise until you can slide the
side handle (6) onto the front of the tool as shown.
Rotate the side handle into the desired position.
Tighten the side handle by turning the grip clockwise.
Fitting and setting the depth stop (fig. A)
Slacken the knob (9).
Insert the depth stop (7) into the mounting hole as
shown.
Set the depth stop (7) to the desired position. The
maximum drilling depth is equal to the distance between
the tip of the drill bit and the front end of the depth stop.
Tighten the knob (9).
Fitting an accessory (fig. B - D)
Clean and grease the shank (10) of the accessory.
Pull back the sleeve (11) and insert the shank into the
tool holder (5).
Push the accessory down and turn it slightly until it fits
into the slots.
Pull on the accessory to check if it is properly locked.
The hammering function requires the accessory to be
able to move axially several centimetres when locked in
the tool holder.
To remove the accessory, pull back the sleeve (11) and
pull out the accessory.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n
0
....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
Labels on tool
The label on your tool may include the following symbols:
Position of date barcode
The Date Code, which also includes the year of
manufacture, is printed into the housing.
Example:
2014 XX JN
Year of manufacturing
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHR323 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHR323 in the language / languages: English as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info