720456
8
Zoom out
Zoom in
Previous page
1/12
Next page
8
Be aware of the location of pipework and wiring.
Apply a pressure of approx. 20 - 30 kg to the tool.
Excessive force does not speed up chiselling but
decreases tool performance and may shorten tool life.
Always hold the tool firmly with both hands and ensure a
secure stance (FIG. C). Always operate the tool with the
side handle properly mounted.
Proper hand position (FIG. C)
Warning: To reduce the risk of serious
personal injury, ALWAYS use proper hand
position as shown.
Warning: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the side handle
(a), with the other hand on the main handle.
Switching on and off (FIG. A)
1. To run the tool, press the switch (b) and turn it in 'ON'
position.
2. To stop the tool, turn it in 'OFF' position and release the
switch (b).
Demolition, chiseling and channelling (FIG. A)
1. Select the appropriate chisel, and clean and grease its
shank.
2. Insert the chisel and check whether it is properly locked.
3. Set the desired impact energy level.
4. Fit and adjust the side handle (a) and make sure it is
firmly tightened.
5. Hold the tool at main handle and side handle (a) and
switch on. The tool now runs in continuous operation.
6. Always switch off the tool when work is finished and
before unplugging.
Various types of chisels are available as an option. Only
Stanley recommended accessories should be used with this
product.
Warning:
Do not use this tool to mix or pump easily combustible or
explosive fluids (benzine, alcohol, etc.).
Do not mix or stir inflammable liquids labelled
accordingly.
Accessory maintenance (FIG. B)
Accessory maintenance at the right time guarantees optimal
results in application and a long and efficient accessory life.
Grind the chisels on grinding discs. Refer to FIG B for the
appropriate angles of the following chisels:
Pointed chisel (h)
Flat chisel (i)
Warning: These chisels can be reground only a
limited number of times. If in doubt, contact your
dealer for recommendations.
Warning: Ensure that the cutting edge does not
show discolouration caused by too much
pressure. This may impair the hardnessof the
accessory.
Maintenance
Your Stanley corded/cordless appliance/tool has been
designed to operate over a long period of time with a
minimum of maintenance. To ensure satisfactory operations,
the tool must be maintained and cleaned regularly
This machine is not user-serviceable. Take the tool to an
authorised Stanley repair agent after approximately 100
hours of use. If problems occur before this time contact
an authorised Stanley repair agent.
Lubrication
Open the cap of the lube oil-injection inlet(e), check the
lube oil in the gearbox, if the lube oil is dirty or
insufficient, replace or add the adequate amount of lube
oil provided by the company.
Cleaning
Warning: Blow dirt and dust out of the main
housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear
approved eye protection and approved dust mask when
performing this procedure.
ENGLISH (Original instructions)
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHM10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHM10 in the language / languages: English as an attachment in your email.

The manual is 1,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info