720456

Stanley STHM10 Manual

7
Zoom out
Zoom in
Previous page
1/12
Next page
7
Features
This tool includes some or all of the following features.
1. Side Handle
2. Switch
3. Electronic impact energy control dial
4. Chisel position index collar
5. Lube oil-injection inlet
6. Tool holder / sleeve
7. Service indicator
Assembly and adjustments
WARNING: To reduce the risk of injury, turn unit
off and disconnect machine from power source
before installing and removing accessories,
before adjusting or changing set-ups or when making
repairs. Be sure the trigger switch is in the OFF position. An
accidental start-up can cause injury.
Inserting and removing SDS-Max accessories (FIG. A1)
This tool uses SDS-Max chisels (refer to the inset in FIG A1
for a cross-section of a chisel shank). We recommend to
use professional accessories only.
1. Clean and grease the chisel shank.
CAUTION: Do not apply lubricant to the
machine.
2. Insert the chisel shank into the bit holder/tool sleeve (f).
Press and turn the chisel slightly until the sleeve snaps
into position.
3. Pull on the chisel to check if it is properly locked. The
hammering function requires the chisel to be able to
move axially several centimetres when locked in the tool
holder.
4. To remove a chisel, pull back the tool holder/ sleeve (f)
and pull the chisel out of the tool holder.
WARNING: Always wear gloves when you
change accessories. The exposed metal parts
on the tool and accessory may become extremly hot during
operation.
Indexing the chisel position (FIG. D)
The chisel can be indexed and locked into 12 different
positions.
1. Insert the chisel as described above.
2. Pull forward and rotate the chisel position collar (d) in the
direction of the arrow until the chisel is in the desired
position.
Setting the electronic impact power control dial (FIG. A)
Turn the dial (c) to the desired level. The higher the number,
the greater the impact energy. With dial settings from «1»
(low) to «6» (full power) the tool is extremely versatile and
adaptable for many different applications. The required
setting is a matter of experience, for example:
• When chiselling soft, brittle materials or when minimum
break-out is required, set the dial to «1» or «2» (low);
• When breaking harder materials, set the dial to «6» (full
power).
Fitting the side handle (FIG. A)
The side handle (a) can be mounted on the front of the
machine to suit both right hand and left hand users.
WARNING: Always operate the machine with
the side handle properly mounted..
1. Unscrew the side handle clamp knob (g).
2. Adjust the side handle (a) to the desired angle.
3. Slide and rotate the side handle to the desired position.
4. Lock the side handle in place by tightening the clamp
knob (g).
Operation instructions for use
WARNING:
• Always observe the safety instructions and applicable
regulations.
(Original instructions) ENGLISH
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHM10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHM10 in the language / languages: English as an attachment in your email.

The manual is 1,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info