720587

Stanley SSW21 Manual

9
Zoom out
Zoom in
Previous page
1/24
Next page
(Original instructions) ENGLISH
9
If there is a pilot light on the starter device, it should go out.
• Water jet control lever (19).
Warning! During operation the appliance must be
positioned as shown in Fig. D on a firm, stable surface.
Start-up (see Fig. D)
1. Turn on the water supply tap fully.
2. Release the safety catch (20).
3. Depress the gun trigger for a few seconds and start up the
appliance using the starter device (ON/I).
Warning! Before starting up the appliance check that it
is receiving water correctly; use of the appliance without
water will damage it. Do not cover the ventilation grilles when
the appliance is in use.
TSS Models - In TSS models with automatic delivery flow
cut-o system:
a. When the gun trigger is released, the dynamic pressure
automatically cuts out the motor;
b. When the gun trigger is depressed, the automatic drop in
pressure starts the motor and the pressure is restored
after a very slight delay;
c. If the TSS is to function correctly all gun trigger releasing
and depressing operations, must be at least 4 - 5 seconds
apart.
To prevent damage to the appliance, do not allow it to operate
dry and check that it is properly supplied with water. For
models without TSS, to prevent damage to the appliance due
to an increase in water temperature, do not cut off the jet of
water for more than 5 minutes with the appliance running.
Stopping
1. Set the starter device switch on (OFF/0).
2. Depress the gun trigger and discharge the residual
pressure inside the pipes.
3. Engage the safety catch (20).
Restarting
1. Release the safety catch (20).
2. Depress the gun trigger and discharge the residual air
inside the pipes.
3. Set the starter device on (ON/I).
Storage
1. Turn o the water supply tap.
2. Discharge the residual pressure from the gun until all the
water has come out of the appliance.
3. Switch the appliance off (OFF/0).
4. Remove the plug from the socket.
5. Drain and wash out the detergent tank at the end of the
working session. To wash out the tank, use clean water
instead of the detergent.
6. Engage the gun safety catch (20).
Recommended cleaning procedure
Dissolve dirt by applying the detergent mixed with water to the
surface while still dry. When dealing with vertical surfaces
work from the bottom upwards. Leave the detergent to act for
1-2 minutes but do not allow the surface to dry. Starting from
the bottom, use the high pressure jet at a minimum distance of
30cm. Do not allow the rinse water to run onto unwashed
surfaces. In some cases, scrubbing with brushes is needed to
remove dirt. High pressure is not always the best solution for
good washing results, since it may damage some surfaces.
The finest adjustable nozzle jet setting or the rotopower
nozzle should not be used on delicate or painted parts, or on
pressurised components (e.g tyres, inflation valves, etc.).
Effective washing depends on both the pressure and volume
of the water used, to the same degree.
MAINTENANCE (Fig. E)
Any maintenance operations not covered by this chapter
should be carried out by an authorized sales and service
centre.
Warning! Always disconnect the plug from the power
socket before carrying out any work on the appliance.
Cleaning the nozzle
1. Disconnect the lance from the nozzle.
2. Remove any dirt deposits from the nozzle hole using the
tool (4).
Cleaning the filter
Inspect the inlet filter (8) and detergent filter (if fitted) before
each use, and clean in accordance with the instructions if
necessary.
Unjamming the motor (On models with this feature)
In case of lengthy stoppages, limescale sediments may cause
the motor to seize. To unjam the motor, turn the drive shaft
with a tool.
End-of-season storage
reat the appliance with non-corrosive, non-toxic antifreeze
before storing it away for winter. Put the appliance in a dry
place, protected from frost.
STORAGE AND TRANSPORTATION (Fig. E)
Store the accessories as shown in Fig. E.
Transport the machine as shown in Fig. E.
HOW TO AVOID DAMAGING SURFACES
Warning!
• Using the appliance to wash tyres may damage the tyre
and can be dangerous.
• Never point the high pressure jet straight at the tyre.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SSW21 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SSW21 in the language / languages: English, French as an attachment in your email.

The manual is 7,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info