720587
8
Zoom out
Zoom in
Previous page
1/24
Next page
ENGLISH (Original instructions)
8
Vehicle engines may be washed only if the dirty water is
disposed of as per regulations in force.
Intake water temperature: See data plate on the
appliance.
Intake water pressure: min. 0.1 MPa - max. 1 MPa.
Operating ambient temperature: Above 0 °C.
The appliance is compliant with the IEC 60335-1 and IEC
60335-2-79 standards.
OPERATOR
The symbol illustrated in Fig. A identifies the appliance’s
intended operator (professional or non-professional).
MAIN COMPONENTS (Fig. A)
1. Lance
2. Gun with safety catch
3. High pressure hose
4. Nozzle cleaning tool
5. Rotating nozzle kit
6. Nozzle
7. Adapter
8. Water filter
9. Detergent kit
10. Electric cable with plug
11. Wheels
12. Hose reel
13. Handle
14. Lever
15. Brackets
Starter device (18)
The starter device prevents accidental use of the appliance.
Caution! Safety devices:
Do not tamper with or adjust the safety valve setting.
Safety valve and/or pressure limiting valve. The safety
valve is also a pressure limiting valve. When the gun trigger
is released, the valve opens and the water recirculates
through the pump inlet or is discharged onto the ground.
Thermostat valve (where fitted) If the water temperature
exceeds the temperature set by the manufacturer, the
thermostat valve discharges the hot water and draws in an
amount of cold water equal to the amount of water
discharged, until the correct temperature is restored.
Safety catch (20): prevents accidental spraying of water.
Overload cutout: stops the appliance in case of overload.
INSTALLATION (Fig. B)
Assembly
Warning! All installation and assembly operations must
be performed with the appliance disconnected from the
mains power supply.
The assembly sequence is illustrated in Fig. B.
Fitting the rotating nozzle
The rotating nozzle kit delivers greater washing power. Use of
the rotating nozzle may cause a reduction in pressure of 25%
compared to the pressure obtained with the adjustable nozzle.
However, the rotating nozzle kit delivers greater washing
power due to the rotation of the water jet.
Warning! Depending on the application, shielded
nozzles can be used for igh preassure cleaning, which
will reduce the emission of hydrous aerosol dramatically.
However, not all applications allow the use of such a device. If
shielded nozzles are not applicable for the protection against
aerosols, a respiratory mask of class FFP 2 or equivalent may
be needed, depending on the cleaning enviroment.
Electrical connection
Warning! Check that the electrical supply voltage and
frequency (V/Hz) correspond to those on the appliance
data plate (Fig. B8).
Use of extension cables: Use cables and plugs with “IPX5”
protection level. The cross-section of the extension cable
should be pro- portionate to its length; the longer it is, the
greater its cross-section should be.
Water supply connection
Caution! Only clean or filtered water should be used for
intake. The delivery of the water intake tap should be
equal to that of pump capacity.
Place the appliance as close to the water supply system as
possible.
Connection points:
Water outlet (OUTLET)
Water inlet with filter (INLET)
Connection to the mains water supply
The appliance may only be connected directly to the mains
drinking water supply if the supply hose is fitted with a
backflow preventer valve as per current regulations in force.
Make sure that the hose is at least Ø 13 mm, that it is
reinforced and that it is not more than 25 m long.
ADJUSTMENT INFORMATION (Fig. C)
Adjusting the spray nozzle (for models with this feature)
Water flow is adjusted by regulating the nozzle (6).
Adjusting the detergent To deliver detergent at the correct
pressure, set the nozzle (6) on or fit the detergent kit
(9) (where available) as shown.
USE OF THE APPLIANCE (Fig. D)
Controls
Starter device (18)
Set the starter switch on (ON/I) to:
a. Start the motor (In models without TSS device);
b. Set the motor ready to start (In models with TSS device).
If there is a pilot light on the starter device, it should light up.
Set the starter device switch on (OFF/0) to stop the appliance.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SSW21 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SSW21 in the language / languages: English, French as an attachment in your email.

The manual is 7,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info