720574

Stanley SLM-196-510-SP Manual

13
Zoom out
Zoom in
Previous page
1/93
Next page
13
Maintaining the Spark Plug
A worn spark plug or a spark gap that is too large will
result in a reduction of engine performance.
1. Disconnect the spark plug connector (12) from the
spark plug by simultaneously pulling and turning.
2. Unscrew the spark plug anticlockwise using the spark
plug socket.
3. Check the spark gap using a feeler gauge (available
from specialist shops). The spark gap must be at least 0.7
mm.
4. Clean the spark plug with a wire brush.
5. Insert the cleaned and adjusted spark plug or replace
a damaged spark plug with a new one
Changing the Engine Oil
To change the engine oil, tip the equipment
on a inclined surface .
• Change the engine oil for the first time after around
5 operating hours then every 50 operating hours or
annually.
• Change the engine oil when the engine is warm.
• Dispose of the used oil in an ecofriendly manner
1. Open the oil drain plug (8)
2. Drain the engine oil into a suitable container.
3. Wipe up spilt engine oil and screw back in the oil
drain plug (8).
4. Stand the equipment level and refill the engine oil
Sharpening / Changing the Blades
• Always have a blunt blade resharpened by a specialist
workshop, as an imbalance check can be carried out
there.
• Always have a specialist workshop change a damaged
or imbalanced blade. Incorrect installation can result in
serious injury.
Adjusting the Carburettor
The carburettor has been preset in the factory for
- Remove the grass collection box ( 20) if it is installed.
- Adjust the cutting height to position 8
- Set the upper handle bar (2) to around 5° in the
direction of the equipment.
Do not squash the Bowden cables (4) when doing this.
Risk of injury if the equipment tips back.
• Always keep the equipment clean. To
clean, use a toothbrush or cloth but no
corrosive cleaning agents or solvents.
Do not use water to clean the engine as
it could contaminate the fuel system.
• After mowing, remove plant remains
that are stuck to the equipment by using a piece of wood
or plastic. Clean the vent holes, ejection hole and blade
area especially. Do not use hard
or pointed objects, which could damage
the equipment.
• Oil the wheels from time to time.
• Before each use, check the lawnmower for obvious
defects such as loose, worn or damaged parts. Check
that all nuts bolts and screws are sitting firmly.
• Check covers and guards for damage
and that they are sitting correctly. Replace
if necessary.
Replacing the Air Filter
Do not operate the equipment without the air filter
otherwise dust and dirt will get into the engine and
result in damage to the machine.
1. Loosen the screw on the air filter cover (15) and flip
open the cover.
2. Remove the air filter (14).
3. Replace the air filter with a new filter.
4. To install, insert the new air filter (14) in the air filter
cover (15).
5. Flip the air filter cover closed and screw it back
together.
G
B
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SLM-196-510-SP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SLM-196-510-SP in the language / languages: English, German, Danish, Italian, Portuguese, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 4,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info