722516
7
Zoom out
Zoom in
Previous page
1/76
Next page
7
ENGLISH
(Original instructions)
Dry vacuum cleaning
To empty tank (FIG. F)
The sound of the motor changes and suction is reduced when
the tank is full.
u Turn vacuum off. Remove the battery pack.
u Unlatch tank latches (5) and remove power head from
the tank.
u Empty contents of tank into suitable container.
u Clean or change lter (18). See Filter section of this
manual.
u Inspect vacuum for damage by foreign objects.
Contact the nearest Stanley Fat Max authorized service
center for replacement of damaged or missing parts.
u Replace power head (3) onto the tank (4) and latch
securely.
Wet vacuum cleaning
Warning! Do not tilt vacuum when in use.
If vacuum has liquid in the tank it may spill out from the
exhaust port.
Warning! Ensure battery port and terminals are dry and clean
before installing battery pack.
The lter must be removed before using the vacuum to
clean liquids. See Filter section of this manual.
To empty tank
The sound of the motor changes and suction is reduced
when the tank is full.
u Turn vacuum off. Remove the battery pack.
u Unlatch tank latches (5) and remove power head from
the tank.
u Empty contents of tank.
u Inspect vacuum for damage by foreign objects. Contact
the nearest Stanley Fat Max authorized service center for
replacement of damaged or missing parts.
u Dry inside of power head and tank with a clean cloth.
u Replace power head (3) onto the tank (4) and latch
securely.
Filter
Filter care
The wet/dry filter (18) included with this vacuum is a long
life filter. To be effective in minimizing dust recirculation the
filters MUST be installed correctly and in good condition.
Note: A clean filter is the most important factor in the
operation and efficiency of any vacuum. If the filter becomes
clogged beyond cleaning, damaged, or fails to operate
properly, replace only with a reccomended replacement.
To clean or change the filter (Fig. G)
u Turn vacuum off. Remove the battery pack.
u Unlatch the tank latches (5) and remove the power
head from the tank as shown in gure D.
Unlock the lter lock (19) by twisting it counter clockwise.
Pull the lter (18) out to remove it from the power head.
u Clean the lter by shaking off excess dust, tapping into
a waste receptacle, then rinsing under running water.
Depending on the condition of the lter, a water wash is
not always required. Do not use a brush to clean lter.
u Reinstall lter and secure the lter lock onto power
head. Twist the lter lock clockwise and ensure the lter
is locked in place.
u Replace power head onto the tank and secure latches.
Note: Please contact your local service center or visit our
website www.stanley.eu/3 to purchase a filter.
Blower
The blower function can be used to remove debris from
behind small spaces, to dry a damp oor, to blow grass
clippings or leaves from an outside walk, patio, etc.
To use as a blower (Fig. H)
u Empty the tank following the instructions under the
Vacuum Cleaning section of this manual.
u Twist the vacuum hose (8) counter clockwise to remove
from the intake port.
u Align the hose end (16) with the side exhaust port (10),
ensuring the hose alignment lock (15) is aligned with the
arrow (20) above the side exhuast port.
u Insert the hose end into the side exhaust port and twist
clockwise to lock in place.
Hose and accessory storage
When the vacuum is not in use, remove the battery pack.
The vacuum hose can be wrapped around appliance,
underneath the battery interface, and secured with the
hose clip (7) also located at the back of the vacuum. The two
accessories (crevice tool and wide nozzle) can be stored on
board the vacuum as well.
Troubleshooting guide
Problem Possible cause Possible Solution
Unit will
not start Battery pack not
installed properly.
Battery pack not
charged.
Internal compo-
nents too hot.
Brushes worn
out.
Check battery pack installation.
Check battery pack charging require-
ments.
Allow tool to cool down.Have motor
replaced by an authorized Stanley Fat
Max service center.
Have brushes replaced by an authorized
Stanley Fat Max
service center.
Battery
pack
will not
charge.
Battery pack
not inserted into
charger.
Charger not
plugged in.
Surrounding air
temperature too
hot or too cold.
Insert battery pack into
charger until LED illuminates.
Plug charger into a working outlet. Refer
to “Important charging notes” for more
details.
Move charger and battery pack to a
surrounding air temperature below 10 °C
or above 40 °C.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SFMCV002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SFMCV002 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info