Manual Stanley SFMCS701 (page 14 of 184) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

720684

Zoom out

Zoom in

1/184

ENGLISH

(Original instructions)

Fully Charged:

Green LED Solid

Hot/Cold Pack Delay:

Green LED Intermittent

Red LED Solid

Note: The compatible charger(s) will not charge a faulty

battery pack. The charger will indicate a faulty battery pack by

refusing to light.

Note: This could also mean a problem with a charger. If the

charger indicates a problem, take the charger and battery

pack to be tested at an authorized service centre.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Hot/Cold Pack Delay

When the charger detects a battery that is too hot or too cold,

it automatically starts a Hot/Cold Pack Delay, the green LED

(21a) will ash intermittently, while the red LED (21b) will

remain on continuously, suspending charging until the battery

has reached an appropriate temperature. The charger then

automatically switches to the pack charging mode. This

feature ensures maximum battery life.

Battery state of charge indicator (Fig. C)

The battery includes a state of charge indicator to quickly

determine the extent of battery life as shown in gure B. By

pressing the state of charge button (15a) you can easily view

the charge remaining in the battery as illustrated in gure C.

Fitting and removing the battery (g. D, E)

u To t the battery (15), line it up with the receptacle on the

tool (22). Slide the battery into the receptacle and push

until the battery snaps into place.

u To remove the battery, push the battery release button

(15b) while at the same time pulling the battery out of the

receptacle as shown in gure E.

Changing or Installing a New Saw Blade (Fig. G,

H, I)

Warning! To reduce the risk of serious personal injury, turn

tool off and remove the battery pack before transporting,

making any adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

Removing the Blade

u Remove battery pack (15) from the saw.

u Raise the arm to the upper position and raise the lower

guard (4) as far as possible.

u Loosen, but do not remove the guard bracket front screw

(24) until the bracket (25) can be raised far enough to

access the blade screw (26). Lower guard will remain

raised due to the position of the guard bracket screw.

u Depress the spindle lock button (28) while carefully rotat-

ing the saw blade (29) by hand until the lock engages.

u Keeping the button depressed, use the other hand and the

hex side of the wrench provided to loosen the blade screw

(26). (Turn clockwise, left-hand threads.)

u Remove the blade screw (26) using the hex side of the

wrench provided, the outer clamp washer (30) and blade

(29). The inner clamp washer (31) may be left on the

spindle (32).

Installing a Blade

u Remove battery pack (15) from the saw.

u With the arm raised, the lower guard (4) held open and

the guard bracket (25) raised, place the blade (29) on the

spindle (32) and against the inner blade clamp (31) with

the teeth on the blade pointing in the direction of rotation

as marked on the saw.

u Assemble the outer clamp washer (30) onto the spindle

(32).

u Install the blade screw (26) and, engaging the spindle lock

(28), tighten the screw (26) rmly with wrench provided

(turn counterclockwise, left-hand threads).

u Return the guard bracket (25) to its original full down posi-

tion and rmly tighten the guard bracket screw (24) to hold

bracket in place.

Cut line guidance system

Warning! Do not stare into work light. Serious eye injury could

result.

Note: The battery must be charged and connected to the

mitre saw.

The cut line guidance system can only be turned On or Off by

the work light switch (16).

To cut through an existing pencil line on a piece of wood, turn

on the cut line guidance system using the work light switch

(16) (not with the main trigger), then pull down on the operat-

ing handle (2) to bring the saw blade close to the wood.

The shadow of the blade will appear on the wood. This

shadow line represents the material that the blade will remove

when performing a cut.

To correctly locate your cut to the pencil line, align the pencil

line with the edge of the blade’s shadow. Keep in mind that

you may have to adjust the mitre or bevel angles in order to

match the pencil line exactly.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SFMCS701 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley SFMCS701 Manual

Product: