720559
19
Zoom out
Zoom in
Previous page
1/192
Next page
17
ENGLISH
1. Use both hands to grip pole saw as shown in FigureO. Use
a firm grip. Thumbs and fingers must wrap around pole saw
handle and pole. Keep fingers away from sawdust exhaust
chute
26
shown in FigureQ.
2. Never operate while in a tree, in any awkward position or on
a ladder or other unstable surface. You may lose control of
pole saw causing severe injury.
3. Follow directions below to trim atee.
a. Make sure pole saw is running at full speed before
making a cut. When starting a cut, place moving saw
chain
14
against limb. Hold pole saw firmly in place to
avoid possible bouncing or skating (sideways movement)
of polesaw.
b. Guide pole saw using light pressure. Make first cut
152mm from tree trunk on underside of limb. Use top of
guide bar
13
to make this cut. Cut 1/3 through diameter
of limb. Then make the finish cut from the top. If you try
to cut off thick branches from the bottom, the branch
may close in and pinch the saw chain in the cut. If you try
to cut off thick branches from the top, without a shallow
undercut, the branch may splinter. Do not force pole saw.
The motor will overload and can burn out. It will do the
job better and safer at the rate for which it wasintended.
c. Remove pole saw from cut while it is running at full
speed. Stop pole saw by releasing trigger switch
4
.
Make sure saw chain has stopped before setting pole
sawdown.
Saw Chain Sharpness
CAUTION: Sharp chain. Always wear protective gloves
when handling the chain. The chain is sharp and can cut
you when it is notrunning.
IMPORTANT: The chain cutters will dull immediately if they
touch the ground, stones, masonry or a nail whilecutting.
To get the best possible performance from your chain saw
it is important to keep the teeth of the saw chain sharp.
Chain sharpening services are available from your nearest
STANLEYFATMAX servicecenter.
NOTE: Each time the saw chain is sharpened, it loses some
of the reduced kickback qualities and extra caution should be
used. It is recommended that a saw chain be sharpened no
more than fourtimes.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regularcleaning.
WARNING:To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can causeinjury.
The charger and battery pack are notserviceable.
Regular maintenance ensures a long effective life for the tool.
After every 10 minutes of use be sure to remove the battery (be
aware the chain and bar can be hot!) check the bar and chain for
correct tension and lubricate per Adjusting Chain Tension and
ChainOiling.
Lubrication
Your power tool requires no additionallubrication.
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing thisprocedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Optional Accessories
WARNING: Since accessories, other than those offered by
STANLEYFATMAX, have not been tested with this product,
use of such accessories with this tool could be hazardous.
To reduce the risk of injury, only STANLEYFATMAX
recommended accessories should be used with
thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
Replacement chain and bar are available from your
nearest STANLEYFATMAX servicecenter.
SFMCPS620 requires replacement chain service part
number STZCS220
. Replacement 20 cm bar, service part
numberSTZCS1220.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
householdwaste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
ourenvironment:
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SFMCPS620 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SFMCPS620 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 18,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info