Manual Stanley SFMCPS620 (page 18 of 192) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

720559

Zoom out

Zoom in

1/192

ENGLISH

Joining Center Extension to Saw Head

Module and Handle Module (Fig. A, M)

Adding the center extension

2

to the handle assembly

1

and

saw head assembly

3

creates a pole saw that is approximately

2.7 m in length as shown in Fig.M.

Refer to to Joining Saw Head Module to HandleModule for

directions on how to attach the middle assembly to the handle

assembly and saw headassembly.



WARNING: Always check to make sure that the sleeve

is completely threaded on and that the red threads are

no longer visible. Not threading the sleeve completely

on could result in the assemblys becoming disconnected

creating a hazardous condition. Periodically check the

connections to insure that no red threads arevisible.

DISASSEMBLY



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Detaching Saw Head Module (Fig. N)



WARNING: Sharp moving blade. To prevent accidental

operation, insure that battery is disconnected from the

handle and that the protective scabbard is in place on the

chain before performing the following operations. Failure

to do this could result in serious personal injury.

When detaching the assemblies, whether it is in the two

assembly or three assembly mode, always detach the saw head

assembly

3

first. To do this, rest the handle assembly

1

on the

ground and grasp the center of the saw head assembly with

one hand as shown in Fig.N. Use your other hand to loosen the

threaded sleeve and then pull the two halves apart. Repeat this

process if the center extension wasattached.

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Proper Hand Position (Fig. O)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the main handle

28

and one hand on the foam gripper

7

Operating the Pole Saw (Fig. A)



WARNING: Read and understand all instructions. Failure

to follow all instructions listed below may result in electric

shock, fire and/or serious personalinjury.



CAUTION: Always reduce the tension off the chain again

after finishing work. The chain contracts as it cools down.

If it is not slackened off, it can damage the polesaw.

IMPORTANT: Never operate a pole saw that is damaged or

improperly adjusted or that is not completely and securely

assembled. Be sure that the saw chain

14

stops moving when

the trigger switch is released. Never adjust the guide bar

13

saw chain when the motor is operating or the battery isattached.

Pole Saw Trimming/Pruning



WARNINGS:

• Never stand directly under the limb you are cutting.

Always position yourself out of the path of fallingdebris.

• Always wear head, eye, foot and body protection.

Wearing body protection helps reduce the risk of injury when

operating thisunit.

• Never stand on a ladder or other unstable support while

using the pole saw. Always avoid any position which can

cause you to loose your balance and cause severeinjury.

• Keep other persons at least 15 m from the work area.

Distractions can cause you to losecontrol.

• Electrocution Hazard. To prevent shock, do not operate

within 15 m of overhead electrical lines. Always check

surrounding area for hidden electricallines.

• Do not extend pole saw switch handle above

shoulderheight.

On/Off Switch (Fig. P)

Always be sure of your footing and grip the pole saw firmly with

both hands with the thumb and fingers encircling the handle. To

turn the tool ON pull the lock button

5

back with your thumb

and then squeeze the trigger switch

4

with your fingers as

shown in Fig.P. (Once the tool is running you can release the

lock button.) To turn the tool OFF, release the trigger.

Branch Removal Hook (Fig. A)



CAUTION: The branch removal hook is not a belt hook.

Your pole saw includes a branch removal hook



18

for the

intended purpose of helping to remove small to moderately sized

prunedbranches.

Pruning With the Pole Saw (Fig. A, O, Q)



WARNING: Let the tool work at its own pace. Do

notoverload.



WARNING: When pruning trees: guard against kickback

which can result in severe injury or death. See Guard

Against Kickback, to avoid the risk of kickback. Do not

overreach. Make sure your footing is firm. Keep feet apart.

Divide your weight evenly on both feet.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SFMCPS620 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 18,39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley SFMCPS620 Manual

Product: