720810

Stanley SFMCN616 Manual

10
Zoom out
Zoom in
Previous page
1/124
Next page
10
ENGLISH
(Original instructions)
Preparing the tool
Warning! NEVER spray or in any other way apply oil,
lubricants or cleaning solvents inside the tool. This can
seriously affect the life and performance of the tool.
Warning! The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
u Read the Safety Instruction section of this manual.
u Wear eye and ear protection.
u Remove battery from tool and fully charge.
u Ensure magazine is empty of all fasteners.
u Check for smooth and proper operation of contact trip and
pusher assemblies. Do not use tool if either assembly is
not functioning properly.
u Keep tool pointed away from yourself and others.
u Insert fully charged battery pack.
Loading the Tool (Fig. F)
Warning! Keep the tool pointed away from yourself and
others. Serious personal injury may result.
Warning! Never load nails with the contact trip or
trigger activated.
Warning! Always remove battery pack before loading or
unloading nails.
Warning! The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
Warning! Keep ngers clear of pusher to prevent injury.
u Insert fasteners into the bottom of the magazine (9).
u Pull pusher latch (10) downward until the nail follower (16)
falls behind the nails as shown in gure F.
u Release the pusher latch(10).
Unloading the Tool
Warning! The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
u Press pusher latch release button (11).
u Manually slide nails towards the bottom of the
magazine (9).
u Open the jam clear door on the nosepiece to verify there
are no nails remaining.
Adjusting Depth (Fig. G)
The depth that the fastener is driven can be adjusted using
the depth adjustment wheel (3) on the side of the tool.
Warning!To reduce risk of serious injury from accidental
actuation when attempting to adjust depth, Always:
u Remove battery pack.
u Engage trigger lock-off.
u Avoid contact with trigger during adjustments.
Depth settings are on a sliding scale on the depth adjustment
indicator (4). The left side indicating the deepest and the right
side indicating the shallowest.
u To drive a nail deeper, rotate the depth adjustment
wheel (3) downwards. This will slide the depth adjustment
indicator (4) to the left on the scale.
u To drive a nail shallower, rotate the depth adjustment
wheel (3) upwards. This will slide the depth adjustment
indicator (4) to the right on the scale.
Work lights (Fig. H)
There are work lights (5) located on each side of the nailer.
Work lights turn on upon depressing the contact trip.
Note: These work lights are for illuminating the immediate
work surface and are not intended to be used as ashlights.
Low Battery Indicator
The work lights will ash and then turn off completely to
indicate low battery.
Jammed Nail Indicator
The work lights will ash continually if a nail becomes jammed
in the nose piece (see Clearing a jammed nail).
Stall Release (Fig. I)
Warning! If a stall occurs, the tool will disable itself and
will require you to reset it. To do so, follow instructions on
clearing a stalled condition. Next remove battery pack and
then reinsert battery pack. The tool will now be operational. If
the nailer is used in a rigorous application where all available
energy in the motor is used to drive a fastener, the tool may
stall. The driver blade did not complete the drive cycle and the
jam/stall indicator will ash. Rotate the stall release lever (6)
on the tool and the mechanism will release.
Note! The tool will disable itself and not reset until the battery
pack has been removed and reinserted. If the unit continues
to stall please review the material and fastener length to be
sure that it is not too rigorous an application. If the driver
blade does not automatically return to the home position
after rotating the stall release lever, proceed to “clearing a
jammed nail”.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SFMCN616 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SFMCN616 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info