Manual Stanley SFMCN616 (page 9 of 124) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

720810

Zoom out

Zoom in

1/124

ENGLISH

(Original instructions)

Hot/Cold Pack Delay

When the charger detects a battery that is too hot or too

cold, it automatically starts a Hot/Cold Pack Delay, the green

LED (13a) will ash intermittently, while the red LED (13b)

will remain on continuously, suspending charging until the

battery has reached an appropriate temperature. The charger

then automatically switches to the pack charging mode. This

feature ensures maximum battery life.

Battery state of charge indicator (Fig. B)

The battery includes a state of charge indicator to quickly

determine the extent of battery life as shown in gure B. By

pressing the state of charge button (12a) you can easily view

the charge remaining in the battery as illustrated in gure B.

Installing and Removing the Battery Pack from

the tool

Warning! Make certain the lock-off button is engaged to

prevent switch actuation before removing or installing battery.

To install battery pack (Fig. C)

u Insert battery pack rmly into tool until an audible click is

heard as shown in gure C. Ensure battery pack is fully

seated and fully latched into position.

To remove battery pack (Fig. D)

u Depress the battery release button (12b) as shown in

gure D and pull battery pack out of tool.

Hang hook (Fig. E)

Warning! Remove nails from magazine before making any

adjustments or servicing this tool. Failure to do so may result

in serious injury.

Warning! To reduce the risk of serious personal injury,

place the forward/reverse button in the lock-off position or

turn tool off and disconnect battery pack before making

any adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

Warning! To reduce the risk of serious personal injury, ensure

the screw (15) holding the hang hook is secure.

Caution: When not in use, place tool on its side on a stable

surface where it will not cause a tripping or falling hazard.

Some tools with large battery packs will stand upright on the

battery pack but may be easily knocked over.

Note: When attaching or replacing the hang hook (14) use

only the screw (15) that is provided. Be sure to securely

tighten the screw.

If the hook is not desired at all, it can be removed from

the tool.

To move the hang hook, remove the screw (15) that holds the

hang hook (14) in place.

Note: Various trackwall hooks and storage congurations are

available.

Please visit our website www.stanley.eu/3 for

further information.

Operation

Warning! Read the section titled Nailer Safety Warnings

at the beginning of this manual. Always wear eye and ear

protection when operating this tool. Keep the nailer pointed

away from yourself and others. For safe operation, complete

the following procedures and checks before each use of

the nailer.

Warning! To reduce the risk of personal injury, disconnect

battery pack from tool and engage trigger lock-off before

performing maintenance, clearing a jammed nails, leaving

work area, moving tool to another location or handing the tool

to another person.

Warning! Keep ngers AWAY from trigger when not driving

fasteners to avoid accidental ring. Never carry tool with nger

on trigger.

u Wear proper eye, hearing and respiratory protection.

u Remove battery pack from tool and engage trigger

lock-off.

u Lock the pusher in the back position and remove all nail

strips from the magazine.

u Check for smooth and proper operation of contact trip and

pusher assemblies. Do not use tool if either assembly is

not functioning properly.

u Never use a tool that has damaged parts.

Warning! Operate the tool with fasteners at a rate not

exceed 30 times/min.

To operate the nailer

Warning! The contact trip needs to be depressed followed by

a full trigger pull for each nail followed by a release of both the

contact trip and trigger after each nail.

Warning!The battery should always be removed and the

trigger lock-off engaged whenever any adjustments are made

or when tool is not in use.

u Fully depress contact trip (8) against the work surface.

u Fully pull trigger (1) and motor will start. (nail will drive into

work surface).

u Release trigger.

u Lift contact trip off work surface.

u Repeat the above 4 steps for next application

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SFMCN616 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley SFMCN616 Manual

Product: