720477
18
Zoom out
Zoom in
Previous page
1/196
Next page
16
ENGLISH
Regular maintenance ensures a long effective life for your
chainsaw.
Chain and Bar
After every few hours of use, remove the sprocket cover, guide
bar and chain and clean thoroughly using a soft bristle brush.
Ensure oiling hole on bar is clear of debris. When replacing dull
chains with sharp chains it is good practice to flip the chain bar
from bottom totop.
Saw Chain Sharpening (Fig. O–Q)
CAUTION: Sharp chain. Always wear protective gloves
when handling the chain. The chain is sharp and can cut
you when it is notrunning.
WARNING: Sharp moving chain. To prevent accidental
operation, ensure that battery is removed from the tool
before performing the following operations. Failure to do
this could result in serious personalinjury.
NOTE: The cutters will dull immediately if they touch the
ground or a nail whilecutting.
To get the best possible performance from your chain saw it is
important to keep the teeth of the chain sharp. Follow these
helpful tips for proper saw chain sharpening:
1. For best results use a 4.5mm file and a file holder or filing
guide to sharpen your chain. This will ensure you always get
the correct sharpeningangles.
2. Place the file holder flat on the top plate and depth gauge
of thecutter.
3. Figure O- Keep the correct top plate
21
filing angle line
of 30° on your file guide parallel with your chain (file at 60°
from chain viewed from the side).
4. Sharpen cutters on one side of the chain first. File from the
inside of each cutter to the outside. Then turn your saw
around and repeat the processes (2,3,4) for cutters on the
other side of thechain.
NOTE: Use a flat file to file the tops of the rakers (portion of
chain link in front of the cutter) so they are about 0.635mm
below the tips of the cutters as shown in FigureP.
5. Figure Q- Keep all cutter lengthsequal.
6. If damage is present on the chrome surface of the top plates
or side plates, file back until such damage isremoved.
CAUTION: After filing, the cutter will be sharp, use extra
caution during thisprocess.
NOTE: Each time the chain is sharpened, it loses some of the
low kickback qualities and extra caution should be used. It
is recommended that a chain be sharpened no more than
fourtimes.
Accessories
WARNING: The use of accessories not recommended in
this manual may behazardous.
Replacement chain and bar are available from your nearest
STANLEYFATMAX authorized service center. For use only with
low kick back bar andchain.
Available bars and chains for SFMCCS630:
Bar: 30cm service part number N727097
Chain: 30cm service part number N580237
Optional Accessories
WARNING: Since accessories, other than those offered by
STANLEYFATMAX, have not been tested with this product,
use of such accessories with this tool could be hazardous.
To reduce the risk of injury, only STANLEYFATMAX
recommended accessories should be used with
thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
Maintenance
Your STANLEYFATMAX power tool has been designed
to operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends upon
proper tool care and regularcleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can causeinjury.
The charger and battery pack are notserviceable.
Lubrication
Refer to Saw Chain and Guide Bar Oiling (Fig.H)
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing thisprocedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
householdwaste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
Run the battery pack down completely, then remove it from
thetool.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SFMCCS630 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SFMCCS630 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 23,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info