720476

Stanley SCS-52 JET Manual

12
Zoom out
Zoom in
Previous page
1/158
Next page
12
correctly.
Important! The chain must not slip off the guide bar (1) .
the chain links must be positioned precisely between the
teeth of the sprocket wheel.
the chain adjustment tang on the sprocket wheel must
insert the hole on the guide bar.
- Now t the two guide bar screws (7) again. Only
tighten them by hand at this stage, however.
Tension the saw chain (B10-B11)
Ensure that the guide bar screws (7) for adjusting
the saw chain (2) are only hand tight. Undo them
if necessary.
- To increase the tension of the saw chain (2), turn
the chain adjustment screw (8) clockwise using a
suitable screwdriver.
- To reduce the tension of the saw chain (2), turn
the chain adjustment screw (8) anti-clockwise
using a suitable screwdriver.
The saw chain (2) tension is correct if it can be
raised a maximum of 2 - 3 mm in the centre of the
guide bar (1).
- Tighten the guide bar screws properly after you
have adjusted the saw chain.
Notes
Allow a new saw chain (2) to run for approx. 5
minutes before actually sawing with it. Check the
chain tension again after this time and adjust it if
necessary.
When it is warm, the saw chain (2) will expand
and may sag. This gives rise to the risk tat the saw
chain (2) will jump o the guide bar. Therefore
you must adjust the tension of the chain (2) after
it has carried out its rst sawing work.
Since a saw chain (2) that has been tensioned
22. Screwdriver
23. Primer button
Assembly (B3-B4)
The saw chain and chain guide bar are not supplied
ready-assembled.
To prevent injuries, wear gloves when tting the
saw chain, when tensioning the chain and during
the subsequent chain tension check.
Fit the guide bar
- First disconnect the chain brake. Press the hand
guard (4) towards the top handle for this purpose.
- Remove the sprocket wheel cover (6) by undoing the
two guide bar screws (7).
- Assemble the claw stop (5) according to the picture
above by using the spark plug wrench.(B31)
- Place the guide bar (1) with the notched end on
the two guide bar bolts (7).
Fit the saw chain
(B5-B9)
- Lay out the chain (2) in a loop. Ensure that the
cutting claws point in a clockwise direction.
- Push the chain (2) over the coupling on to the
sprocket wheel on the chainsaw. Ensure that the
chain links are positioned precisely between the
teeth of the sprocket wheel.
- Now place the chain (2) over the tip of the bar.
Ensure that the chain links are positioned in
the guide bar groove.
The saw chain will sag downwards at this time on
the bottom of the guide bar.
- Now t the sprocket wheel cover (6) again.
Ensure that the chain adjustment tang engages
in the hole on the guide bar. Only then will
it be possible to t the sprocket wheel cover (6)
G
B
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SCS-52 JET at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SCS-52 JET in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese as an attachment in your email.

The manual is 6,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info