Manual Stanley SCS-46 JET (page 15 of 126) (English, German, Dutch, French, Italian, Polish)

720475

Zoom out

Zoom in

1/126

wish to improve the setting, contact an approved

workshop.

Storage

Clean the saw chain (2) and guide bar (1) after

every use.

Fit the chain guard (3).

Work instructions (B21-B27)

Obey all the safety regulations.

Never saw with a loose or blunt chain. Always pull

the machine out of the wood whilst the chain is

still moving.

When cutting fallen trees, please note that the

trunk may be under tension.

Trunk under tension on the top. The tree may

spring upwards.

Trunk under tension on the bottom. The tree may

spring downwards.

Use a clamp (for example a saw stool) whenever

possible.

Only use the saw for wood or wooden objects.

Watch for foreign bodies such as nails or stones.

If they come into contact with the moving saw

chain they may be catapulted out and may also

damage the saw chain.

When cutting wood, the claw stop (5) must be

positioned ﬁrmly against the wood and when the

saw is started it must move into the wood. Hold

the saw using the front handle and pull the saw

upwards using the rear handle. The claw stop can

be used as a pivot point for this purpose. To reset the

position of the claw, press gently on the front handle and

pull the saw backwards slightly.

Now place the claw stop a little deeper and then

pull the handle upwards again.

For longitudinal cuts, the chainsaw must be positioned at

as ﬂat an angle as possible. Since the claw stop cannot

be used in this case, take special care with these cuts.

Danger of recoil!

There is always a risk of recoil if the tip of the bar

touches wood or other objects. This makes the

chainsaw impossible to control and may lead to

it being catapulted with great force towards the

operator.

Whenever possible, always saw with the underside

of the bar since if you saw with the top of the bar, the

chainsaw will be catapulted towards the operator if the

chain jams.

Support yourself on the trunk whenever possible

when removing branches from a tree.

Special precautions for felling trees:

Felling trees is extremely dangerous and training

is required for this work. If you are unfamiliar with

this work, you should not attempt it. You must

receive training ﬁrst.

Never attempt to fell trees whose diameter is greater

than the length of the guide bar.

A falling tree may also bring down other trees.

Always use twice the tree length as a danger area

(felling area). Take care also not to disturb

power and telephone cables.

Before starting to fell a tree, you must plan and

clear an escape route. The escape route must be

in the opposite direction to the expected felling

direction.

There must be no spectators, animals or obstacles

in the felling area.

If the saw jams in the tree, never attempt to free it

when the engine is running. Use wooden wedges

to free the saw.

Taking into account the centre of gravity of the

crown and the wind direction, calculate the felling

direction ﬁrst. Ensure that the chainsaw is

running immediately before it comes into contact

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SCS-46 JET in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 3,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley SCS-46 JET Manual

Product: