720471
9
Zoom out
Zoom in
Previous page
1/14
Next page
9
ENGLISH
Do not incinerate the battery pack.
Package Contents
The package contains:
1 Drill/driver
1 Charger
2 Batteries (S2) or 1 Battery (S1)
1 Instruction manual
NOTE: Battery packs and chargers are not included with
N-models.
Check for damage to the tool, parts or accessories which may
have occurred during transport.
Take the time to thoroughly read and understand this
manual prior to operation.
Description (Fig. A)
WARNING: Never modify the power tool or
any part of it. Damage or personal injury could
result.
1. Trigger switch
2. Forward/reverse button
3. Torque adjustment collar
4 Gear shifter
5. Keyless chuck
6. Battery release button
7. Battery pack
8. LED Worklight
Assembly and adjustments
WARNING: Prior to assembly and adjustment,
always remove the battery pack. Always switch
off the tool before inserting or removing the
battery pack.
WARNING: Use only STANLEY battery packs
and chargers.
Inserting and Removing the
Battery Pack from the Tool (Fig. C)
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up can
cause injury.
NOTE: Make sure your battery pack (7) is fully charged.
To install the battery pack into the tool handle
1. Align the battery pack with the rails inside the handle.
2. Slide it firmly into place until you hear the lock snap into
place.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
your charger corresponds to that of your mains.
Your STANLEY charger is double insulated in
accordance with EN 60335; therefore no earth
wire is required.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the STANLEY
service organisation.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for the
power input of your charger (see Technical Data). The
minimum conductor size is 1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable complet
ely.
Proper Hand Position (Fig. A, H)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper hand
position as shown.
To remove the battery pack from the tool
1. Press the release button (6) and firmly pull the battery pack
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Operating Instructions
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SCD12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SCD12 in the language / languages: English, French, Portuguese, Turkish as an attachment in your email.

The manual is 10,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info