720433

Stanley KFFMED1250 Manual

6
Zoom out
Zoom in
Previous page
1/52
Next page
6
ENGLISH
(Original instructions)
Labels on tool
The following pictograms are shown on the tool along with the
date code:
:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
f
Wear ear protectors with Impact drills. Exposure
to noise can cause hearing loss
Electrical safety
#
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
uIf the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Stanley FatMax Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/Off switch
2. Speed selector dial
3. Drilling mode selector
4. Operating mode selector
5. Tool holder
6. Side handle
7. Depth stop
8. Grease cap
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fittingthesidehandle(g.A)
uTurn the grip counterclockwise until you can slide the side
handle (6) onto the front of the tool as shown.
uRotate the side handle into the desired position.
uTighten the side handle by turning the grip clockwise.
Fittingandsettingthedepthstop(g.A)
uSlacken the knob (9).
uInsert the depth stop (7) into the mounting hole as shown.
uSet the depth stop (7) to the desired position. The maxi-
mum drilling depth is equal to the distance between the tip
of the drill bit and the front end of the depth stop.
uTighten the knob (9).
Fittinganaccessory(g.B)
uClean and grease the shank (10) of the accessory.
uPull back the sleeve (11) and insert the shank into the tool
holder (5).
uPush the accessory down and turn it slightly until it ts into
the slots.
uPull on the accessory to check if it is properly locked. The
hammering function requires the accessory to be able to
move axially several centimetres when locked in the tool
holder.
uTo remove the accessory, pull back the sleeve (11) and
pull out the accessory.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, oors or ceilings, check for
the location of wiring and pipes.
Warning! Do not apply chisels when the tool is in the drilling
mode.
Selectingtheoperatingmode(g.D)
The tool can be used in three operating modes.
u To operate the drilling mode selector (3), rotate it towards
the required position, as indicated by the symbols.
u To operate the operating mode selector (4), push the
unlock button (16) and rotate the selector towards the
required position, as indicated by the symbols.
Drilling
u For drilling in steel, wood and plastics, and for screwdriv-
ing set the operating mode selector (4) to the
s
position
and the drilling mode selector (3) to the
r
position.
Hammer drilling
u For hammer drilling in masonry and concrete, set the
operating mode selector (4) to the
s
position and the
drilling mode selector (3) to the
s
position. When ham-
mering, the tool should not bounce and run smoothly. If
necessary, increase the speed.
Hammering
u For hammering with spindle lock, and for light chiselling
and chipping, set the operating mode selector (4) to the
q
position and the drilling mode selector (3) to the
s
position.
u When changing from hammer drilling to chiselling, turn
the chisel to the desired position. If resistance is felt
during mode change, slightly turn the chisel to engage the
spindle lock.
Switching on and off
u Select the required speed by turning the speed selector
dial (2).
u To switch the tool on, press the on/off switch (1).
u To switch the tool off, release the on/off switch.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley KFFMED1250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley KFFMED1250 in the language / languages: English, German, French, Polish, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 3,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info