720798
9
Zoom out
Zoom in
Previous page
1/194
Next page
9
GB
MAINTENANCE
To Clean the Lens
Blow off loose dust and dirt with compressed air. Carefully
wipe the surface with a moist cotton swab. Don’t use abrasive
or solvent.
To Clean the Thermometer Housing
Use soap and water on a damp soft cloth. Don’t use abrasives
or solvent.
NOTE:
Do not immerse the thermometer in water, and do not let any
liquid enter the case.
SPECIFICATION
Temperature Range: -50°C to 1350°C (-58°F to 2462°F)
Accuracy:
Range Accuracy*
Celsius -50°C to - 20°C ± 5°C
-20°C to 200°C ± (1.5% of reading + 2°C)
200°C to 538°C ± (2.0% of reading + 2°C)
538°C to 1350°C ± (3.0% of reading + 5°C)
Fahrenheit -58°F to -4°F ± 9°F
-4°F to 392°F ± (1.5% of reading + 3.6°F)
392°F to 1000°F ± (2.0% of reading + 3.6°F)
1000°F to 2462°F ± (3.0% of reading + 9°F)
* Accuracy specication assumes that the ambient operating
temperature is 18°C to 28°C (64°F - 82°F) and the operating
relative humidity is less than 80%.
Specications
Response Time: < 1 sec
Response Wavelength: 8µm to 14µm
Emissivity: Adjustable from 0.1 to 1.0
(0.95 default value)
Distance to Spot Ratio: 20:1
Auto-off: After 1 minute of inactivity
Batteries: 1 x 9V battery,
6F22 or equivalent
IP Rating: IP20
Operating Temperature: Temperature: 0°C to 40°C
Relative humidity: 10% to 95% RH,
noncondensing @
up to 30°C
Storage Temperature: -20°C to 50°C
Laser Class: 2
Laser Power: ≤1mW
Laser Wavelength: 630-680nm
Field of View (Figures D–F)
The farther the thermometer is from a target, the larger the
target area will be, this is known as the distance to spot
(D:S=20:1) ratio. For example: at a distance of 508 mm the spot
will be 25.4 mm in diameter. The thermometer will display the
average temperature across the target area.
DISTANCE: SPOT = 90% Energy
DISTANCE: SPOT ratio 20:1
NOTE: For best accuracy make sure the object to be measured
is larger then the thermometer’s spot size.
The thermometer has a visible red laser point (26) in the centre
of eight outer dots. The red laser point shows the approximate
location where the temperature is being measured. The outer
dot pattern will become larger with distance. Figure E shows the
laser point and outer dots near, Figure F shows the laser point
and outer dots farther away.
NOTE: The laser point is only an approximate location, it is not
an exact location.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley FMHT0-77422 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FMHT0-77422 in the language / languages: All languages as an attachment in your email.

The manual is 14,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info