720798
6
Zoom out
Zoom in
Previous page
1/194
Next page
6
GB
Always insert batteries correctly with regard to polarity
(+ and –), as marked on the battery and the equipment.
Do not short battery terminals.
Do not charge disposable batteries.
Remove dead batteries immediately and dispose of per
local codes.
Do not dispose of batteries in re.
Keep batteries out of reach of children.
Remove batteries when the device is not in use.
Battery Installation (Figure B)
Open the battery cover (10) by gently pressing in at the
locations (23) shown in Figure B. Connect the 9V battery (24)
(6F22 or equivalent), ensuring polarity. Close battery door.
Battery Replacement (Figure B)
When the symbol
appears, the battery is low and
should be replaced.
Wait until the thermometer turns off automatically. Open the
battery cover (10) by gently pressing in at the locations (23)
shown in Figure B. Replace battery with 9V battery (24) (6F22
or equivalent), ensuring polarity is correct. Close battery door.
Components
THERMOMETER (Figure A)
1 Button
2
Button
3
Button
4 MODE Button
5 Built-in 1/4-20 Nut
6 Handle
7 LCD Display
8 IR Sensor
9 Measurement Trigger
10 Battery Cover
11 Laser Pointer
NOTE: The thermometer can be attached to a suitable support
with a 1/4-20 bolt using the thermometer’s built in 1/4-20 nut (5).
LCD INSTRUCTION (Figure A)
12 MAIN DISPLAY shows the present reading or last reading.
13 DATA HOLD indicator appears when the reading on the
main display is locked.
14 MEASUREMENT INDICATOR appears and ashes when
the thermometer is taking measurements.
15 EMISSIVITY DISPLAY shows the present emissivity setting
value. TIP: The symbol
means Emissivity.
16 BACKLIGHT INDICATOR appears when the backlight
function is active.
17 TEMPERATURE UNIT applies to both the main display and
the bottom display.
18 SYMBOLS used to indicate the kind of value being
displayed on the bottom display. EXAMPLE: If the symbol
“ MAX “ appears, the value on the bottom display is the
maximum value.
19 BOTTOM DISPLAY used to display maximum (MAX),
minimum (MIN), difference (DIF), average (AVG), high alarm
value (HAL) and low alarm value (LAL).
20
is the high alarm icon, and is low
alarm icon.
21 LOW BATTERY INDICATOR
: Replace the battery
immediately when the low battery indicator appears.
22 LASER FUNCTION INDICATOR appears when the laser
function is enabled. When this indicator appears, the laser
pointer will emit a laser beam when the trigger is pulled.
BUTTON INSTRUCTIONS (Figure A)
1 Button
Used to change temperature units from Celsius to
Fahrenheit value(s).
When setting emissivity (
), high alarm value (HAL),
or low alarm value (LAL), press this button to
increase the value to be set
2
Button
Press this button to turn on or off the backlight.
To enable or disable the laser function, press
button while pulling and holding the trigger. When the
laser function is enabled, the symbol appears.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley FMHT0-77422 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FMHT0-77422 in the language / languages: All languages as an attachment in your email.

The manual is 14,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info