720710
9
Zoom out
Zoom in
Previous page
1/120
Next page
9
ENGLISH
(Original instructions)
u Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 18°- 24°C. DO NOT charge the battery pack in
an air temperature below +4.5°C, or above +40.5°C. This
is important and will prevent serious damage to the battery
pack .
u The charger and battery pack may become warm to touch
while charging. This is a normal condition, and does not
indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack
in a warm environment such as in a metal shed, or an
uninsulated trailer
u If the battery pack does not charge properly:
u Check current at receptacle by plugging in a lamp or
other appliance
u Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights.
u Move charger and battery pack to a location where the
surrounding air temperature is approximately 18°-
24°C.
u If charging problems persist, take the appliance, battery
pack and charger to your local service center.
u The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily done
previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse affect on the battery pack.
u Foreign materials of a conductive nature such as, but
not limited to, steel wool, aluminium foil, or any buildup
of metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply
when there is no battery pack in the cavity. Unplug charger
before attempting to clean.
u Do not freeze or immerse charger in water or any other
liquid.
Warning! Shock hazard. Do not allow any liquid to get inside
charger. Never attempt to open the battery pack for any
reason.
If the plastic housing of the battery pack breaks or cracks,
return to a service center for recycling.
Installing and removing the battery pack from the
appliance
Warning! Make certain the lock-off button is not engaged to
prevent switch actuation before removing or installing battery.
To install battery pack
Insert battery (A1) into appliance until an audible click is
heard (Figure A). Ensure battery pack is fully seated and fully
latched into position.
To remove battery pack
Depress the battery release button (B1) as shown in Figure B
and pull battery pack out of appliance.
Operation
Warning! Read the section titled Nailer Safety Warnings at
the beginning of this manual. Always wear eye and ear protec-
tion when operating this tool.
Keep the nailer pointed away from yourself and others. For
safe operation, complete the following procedures and checks
before each use of the nailer.
Warning! To reduce the risk of personal injury, disconnect
battery pack from tool and engage trigger lock-off before
performing maintenance, clearing a jammed nails, leaving
work area, moving tool to another location or handing the tool
to another person.
Warning! Keep ngers AWAY from trigger when not driving
fasteners to avoid accidental ring. Never carry tool with nger
on trigger.
u Wear proper eye, hearing and respiratory protection.
u Remove battery pack from tool and engage trigger lock-
off.
u Lock the pusher in the back position and remove all nail
strips from the magazine.
u Check for smooth and proper operation of contact trip and
pusher assemblies. Do not use tool if either assembly is
not functioning properly.
u Never use a tool that has damaged parts.
To operate the nailer
Warning! The contact trip needs to be depressed followed by
a full trigger pull for each nail followed by a release of both the
contact trip and trigger after each nail.
Warning!The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
u Fully depress contact trip against the work surface.
u Fully pull trigger and motor will start. (nail will drive into
work surface).
u Release trigger.
u Lift contact trip off work surface.
u Repeat the above 4 steps for next application
Preparing the tool
Warning! NEVER spray or in any other way apply oil, lubri-
cants or cleaning solvents inside the tool. This can seriously
affect the life and performance of the tool.
Warning! The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
u Read the Safety Instruction section of this manual.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley FMC792 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FMC792 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info