Manual Stanley FMC792 (page 7 of 120) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

720710

Zoom out

Zoom in

1/120

ENGLISH

(Original instructions)

Careless handling of the nailer can result in unex-

pected ring of fasteners and personal injury.

u Do not point the tool towards yourself or anyone

nearby. Unexpected triggering will discharge the fastener

causing injury.

u Do not actuate the tool unless it is placed rmly

against the workpiece. If the tool is not in contact, the

fastener may be deected away from your target.

u Disconnect the tool from the power source when the

fastener jams in the tool. While removing a jammed

fastener, the nailer may be accidentally activated if it is

plugged in.

u Do not use this tool for fastening electrical cables.

It is not designed for electric cable installation and may

damage the insulation of electric cables thereby causing

electric shock or re hazards.

Residual risks

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings.

These risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving parts.

u Injuries caused when changing any parts, blades or ac-

cessories.

u Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed when

using your tool (example:- working with wood, especially

oak, beech and MDF.)

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured in

accordance with a standard test method provided by EN50636

and may be used for comparing one tool with another. The

declared vibration emission value may also be used in a

preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Labels on tool

The following symbols are shown on the tool along with the

date code:

Warning! To reduce the risk of injury, the user

must read the instruction manual.

Warning! To reduce the risk of injury, the

user must wear ear and eye protection.

Keep hands and body parts clear of

immediate work area.

Additional safety instructions for batteries and

chargers

Batteries

u Never attempt to open for any reason.

u Do not expose the battery to water.

u Do not store in locations where the temperature may

exceed 40 °C.

u Charge only at ambient temperatures between 10 °C and

40 °C.

u When disposing of batteries, follow the instructions given

in the section "Protecting the environment".

u Do not damage/deform the battery pack either by puncture

or impact, as this may create a risk of injury and re.

u Do not charge damaged batteries.

u Under extreme conditions, battery leakage may occur.

When you notice liquid on the batteries Carefully wipe the

liquid off using a cloth. Avoid skin contact.

u In case of skin or eye contact, follow the instructions

below.

Warning! The battery uid may cause personal injury or

damage to property. In case of skin contact, immediately rinse

with water. If redness, pain or irritation occurs seek medical

attention. In case of eye contact, rinse immediately with clean

water and seek medical attention.

Do not attempt to charge damaged batteries

Chargers

u Use your Stanley Fat Max charger only to charge the

battery in the tool with which it was supplied. Other

batteries could burst, causing personal injury and damage.

u Never attempt to charge non-rechargeable batteries.

u Have defective cords replaced immediately.

u Do not expose the charger to water.

u Do not open the charger.

u Do not probe the charger.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FMC792 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,6 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley FMC792 Manual

Product: