603491
91
Zoom out
Zoom in
Previous page
1/121
Next page
CP590 Page 93
users this function allows entering of signal delay values to fine adjust the calculated
position. The user should enter delay values to fine adjust the position calculated.
Alter : Alternate Solution (TD Coordinate System)
Parameter selected by the user that is applied in the conversion of geographical coordinates
Lat/Lon to TD values. To be used if the position displayed is roughly not correct.
13.2 COMPASS
The CP590 computes compass direction from the constellation of GPS satellites. For the
CP590 to compute direction the vessel must be moving through the water unless connected
to an optional Flux Gate Compass sensor. The Compass menu allows the CP590 to
customize the following selections:
Bearings : Selects between True and Magnetic. When Magnetic Bearings is enabled, the CP590 applies the selected
Magnetic Variation (Auto or Manual, see next paragraph) to compute Magnetic Bearing.
Variation : Allows the user to select Auto or Manual. When Auto mode is selected the CP590 computes the offset
by the current GPS fixed location. Manual mode allows the user to enter in a Magnetic Variation that is
applied in the True conversion.
Calibration : Allows a user to enter in the offset for areas that the vessel may cruise instead of entering in a manual offset
for one location. This offset is useful for cruising vessels or vessels that travel internationally often.
Figure 13.2 - Compass Table
13.3 ALARMS
The Alarms menu is used to select and setup audible and visual Alarms. Available alarms
are Arrival, XTE, Depth, Anchor and Grounding Alarm.
Arrival Alarm
1
: Alerts when the vessel is approaching single destination point or when arriving at a leg in
a Route. Available selections: 0.00 to 9.99Nm.
XTE Alarm
1
: Alerts when the vessel is deviating from a defined course. Available selections: 0.00 to
9.99Nm.
Depth Alarm
1
: Alerts when the received depth Value is lower than the selected value. Available selections:
0000 to 3000ft.
Anchor Alarm
1
: Alerts when the ships moves off a selected locations by a selected distance. Available
selections: 0.00 to 9.99Nm.
Audible Alarm : Enables or disables the alarm beep.
Grounding Alarm
2
: Looks ahead of the vessels heading to see if a potential danger exists. When the Grounding
Alarm is enabled the CP590 will draw a triangle in front of the vessel on the Chart page
showing the area that is being searched as shown below. The depth and range (distance)
of the area the CP590 looks ahead for a shallow area can be set using this function.
Grounding Alarm Range: Allows setting the distance of the grounding alarm zone (the length of the sector to be
detected) among the 0.25, 0.5, 1.0 Nm selections. When a depth or any of the searched objects
is fond in the scanned area, a tick marker is printed on the relative box in the Grounding Alarm
Report page to identify which dangerous objects have been currently detected.
Grounding Alarm Report: Allows displaying a report of the dangerous objects currently detected.
NOTE
1
Please note that the alarm can be activated only if the CP590 is receiving a Fix position or
Simulation mode is activated. Otherwise an error beep is returned and the Alarm value is kept to
Off.
91


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Standard Horizon CP590 - GPS Chart Plotter at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Standard Horizon CP590 - GPS Chart Plotter in the language / languages: English as an attachment in your email.

The manual is 8,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info