584183
13
Zoom out
Zoom in
Previous page
1/26
Next page
XE Series Elliptical
12
STEP 2: HANDLE BAR ASSEMBLY
1. Install the 2 pcs of 17m/m Wave Washers onto the Left and Right side of the Handle Bar
axle.
2. Slide the Left and Right Handle Bars onto the appropriate side of the axle.
3. Put the 2 pcs of 5/16" x 23 x 1.5T Flat Washers onto the 2 pcs of 5/16" x 15m/m Hex
Head Screws and install, and tighten, in the threaded holes in the ends of the axle.
STEP 3: CONNECTING ARM ASSEMBLY
1. Align the hole in the end of the Connecting arms (L&R)(pivoting rod end) with the hole in
the bracket of the Handle Bars (L&R). The rod end should be on the inside of the Handle
Bars (L&R) bracket. Take 2pcs of 5/16" x 1-1/4" Hex Head Screws and install it through
the Handle Bar (L&R) bracket and the rod end. Install 2pcs of 5/16" x 20 x 1.5T Flat
Washers, 5/16" x 7T Nyloc Nuts and11.9 x 8.5 x 16m/m Sleeve Spacer on the 5/16" x
1-1/4" Hex Head Screw and tighten firmly using a 12m/m Wrench on the 5/16" x 7T
Nyloc Nut and one on the 5/16" x 1-1/4" Hex Head Screw.
STEP 4: PLASTICS ASSEMBLY
1. Install the Connecting Arm Covers (L & R) over the connection of the rod end and
Handle Bars (L & R) with 4pcs of M5 x 15m/m Phillips Head Screws and 2pcs of
3.5x12m/m Self Tapping Screws by using the Short Phillips Screw Driver.
2. Install the 2pcs of Wheel Covers using the 4pcs of M5x15m/m Phillips Head Screws.
3. Locate the 2 pcs of Rear Stabilizer Covers and 2 pcs of Middle Stabilizer Covers for the
Rear Rail Assembly and install with 4 pcs of M5 x 15m/m Phillips Head Screws by using
the Phillips Head Screw Driver.
Then install front stabilizer cover with 2 pcs of M5 x 15m/m Phillips Head Screws by
using the Phillips Head Screwdriver.
4. Install the Front Handle Bar Cover (L & R) and Rear Handle Bar Cover (L & R) over the
Handle Bars axle connections with the 6 pcs of 3.5x12m/m Self Tapping Screws by
using Phillips Head Screw Driver.
PLEASE ENSURE ALL FASTENERS ARE TIGHT AFTER THE COMPONENTS HAVE
BEEN ASSEMBLED.
POWER CONNECTOR LOCATED ON
FRONT, LEFT HAND SIDE OF UNIT.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spirit ZE110 2006 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spirit ZE110 2006 in the language / languages: English as an attachment in your email.

The manual is 1,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info