584183

Spirit ZE110 2006 Manual

12
Zoom out
Zoom in
Previous page
1/26
Next page
XE Series Elliptical
11
UNPACKING THE UNIT
1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift
Box over the unit and unpack.
2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged
parts are found, or parts are missing, contact your dealer immediately.
3. Locate the hardware package. The hardware is separated into steps. Remove the tools first.
Remove the hardware for each step as needed to avoid confusion.
STEP 1: CONSOLE MAST ASSEMBLY
1. Locate the Console Mast and Console Mast Cover and slide the Cover onto the Mast as
far as it will go. Make sure the Console Mast Cover is facing the correct way.
2. At the top opening of the Main Frame of the elliptical is a Computer Cable. Unravel and
straighten out the Computer Cable and feed it into the bottom of the console mast tube
and out of the top opening.
3. Install the Console Mast into the receiving bracket in the top of the Main Frame.
NOTE: there is one bolt already installed in the receiving bracket that will engage with the
slot at the bottom of the Console Mast. This needs to be tightened at the end along with
the three other console mast bolts.
4. Put the 1pc of 3/8" x 2T Spring Washer onto the 1pc of 3/8" x 2-1/4" Hex Head Screw and
the 2pcs of 3/8 x 23 x 1.5T Curved Washers onto the 2pcs of 3/8" x 3/4" Hex Head
Screws. Install, and hand tighten, the Hex Head Screw through the left side of the
receiving bracket into the Console Mast.
NOTE: There is a electrical wire running through the Console Mast Tube. Be careful not
to damage or pinch this Computer Cable during this procedure. Damage to the Console
could result. Install, and hand tighten, the 2pc of 3/8" x 3/4" Hex Head Screws through the
front of the receiving bracket into the Console Mast.
5. Using the 13/14m/m Wrench tighten the three bolts, and the fourth bolt which is
pre-installed, firmly. These bolts should be tightened as much as you possibly can.
6. Locate the Console and the 4 pcs of M5 x 10m/m Phillips Head Screws.
7. There will be three electrical wire connectors at the top opening of the Console Mast, two
2 pin Hand pulse Cables, one Computer Cable. Connect these to the mating connectors
on the back of the Console. The connectors are keyed so you cannot plug them in the
wrong way so do not force them. The 2 pin Hand pulse Cables are both the same. It does
not matter how you connect them.
8. Storing the excess wire back into the Console Mast, carefully install the Console onto the
mounting plate of Console Mast and secure using the 4 pcs of M5 x 10m/m Phillips Head
Screws.
Assembly Instructions (ZE120)
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spirit ZE110 2006 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spirit ZE110 2006 in the language / languages: English as an attachment in your email.

The manual is 1,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info