518564
10
Zoom out
Zoom in
Previous page
1/32
Next page
6
Elliptical Trainer
XE295
1. Locate the Console Mast (12) and Console Mast Cover (72); slide the Cover onto the Mast as far as it will
go. Make sure the Console Mast Cover (72) is facing the correct way.
2. At the top opening of the Main Frame (1), there is a Computer Cable (53) tied to a twist tie wire. Feed
the twist tie wire and Computer Cable (53) into the bottom of the Console Mast (12) and out of the
opening at the top.
3. Install the Console Mast (12) into the receiving bracket on the top of the Main Frame (1). Be extremely
careful not to pinch the cables between the tubing. If the cable gets pinched, this may affect the electrical
functions of the console. NOTE: there is one bolt already installed in the receiving bracket that will engage
with the slot at the bottom of the Console Mast. This needs to be tightened last, after the three other
console mast bolts.
4. Place a Split Washer (152) onto the Hex Head Bolt (105) and hand tighten through the left side of the
console mast. Place a Curved Washer (153) onto each Hex Head Bolt (103) and thread both into the
front of the console mast tube. Fasten these front bolts as tight as possible with the wrench (155). Next
rmly tighten the two left side bolts with the same wrench.
5. Connect the two Hand Pulse Cables (47), Resistance Cable (49), and Computer Cable (53) to the back of
the console (43). Do not force the connectors; they will only t one way and are different sizes to prevent
confusion. Store the excessive cable in the Console Mast tube (12).
6. Attach the Console (43) to the bracket of the Console Mast tube with four Phillips Head Screws (116).
Tighten the screws with the Phillips Head Screw Driver (157).
7. Attach the Rear Floor Support (15) to the Rails (2 & 3) with two Button Head Socket Bolts (176) and
Curved Washers (153) on each side. Tighten using the Combination M5 Allen Wrench & Phillips Head
Screw Driver (177).
8. Slide the Rail Assembly into the Main Frame (1). Insert one Button Head Socket Bolt (176) through each
side and attach a Flat Washer (137) and a Nyloc Nut (130) to each joint on the inside.
HARDWARE
STEP 1: Rail Assembly & Console Mast
#137. 3/8” x 19 x 1.5T
Flat Washer
(2 pcs)
#152. 3/8” x 2T
Split Washer
(1 pc)
#153. 3/8” x 23 x 2T
Curved Washer
(6 pcs)
#176. 3/8” x 2-1/4”
Button Head Socket Bolt
(6 pcs)
#103. 3/8” x 3/4”
Hex Head Bolt
(2 pcs)
#105. 3/8” x 2-1/4”
Hex Head Bolt
(1 pc)
#116. M5 x 10mm
Phillips Head Screw
(4 pcs)
#130. 3/8” x 7T
Nyloc Nut
(2 pcs)
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spirit XE-295 2013 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spirit XE-295 2013 in the language / languages: English as an attachment in your email.

The manual is 3,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spirit XE-295 2013

Spirit XE-295 2013 User Manual - Dutch - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info