Manual Spirit XE-295 2013 (page 30 of 32) (English)

518564

Zoom out

Zoom in

1/32

Elliptical Trainer

XE295

1. Wipe down all areas in the sweat path with a damp cloth after each workout.

2. If a squeak, thump, clicking or rough feeling develops the main cause is most likely one of two

reasons:

I. i. The hardware was not sufciently tightened during assembly. All bolts that were installed

during assembly need to be tightened as much as possible. It may be necessary to use a larger wrench

than the one provided if you cannot tighten the bolts sufciently. I cannot stress this point enough; 90% of

calls to the service department for noise issues can be traced to loose hardware or the rear rails

being dirty.

II. ii. Dirt build-up on the rear rails and polyurethane wheels are also a source of noise. Noise from build-up

on the rails can cause a thumping sound that you would swear is coming from inside the main body of the

machine because noise travels, and is amplied, in the tubing of the frame. Clean the rails and wheels with

a lint free cloth and rubbing alcohol. Stubborn build-up can be removed with your thumbnail or a

non-metallic scraper, like the back edge of a plastic knife. After cleaning, apply a small amount of lubricant

on the rails with your ngers or a lint free cloth. You only need a thin coat of lubrication, wipe off any

excess.

3. If squeaks or other noises persist, check that the unit is properly leveled. There are 4 leveling pads on the

bottom of the rear rails, use a 14mm wrench (or adjustable wrench) to adjust the levelers.

General Maintenance

Engineering Mode Menu

The console has built in maintenance/diagnostic software. The software will allow you to change

the console settings from English to Metric and turn off the beeping of the speaker when a key

is pressed for example. To enter the Engineering Mode Menu, press and hold down the Start,

Stop and Enter keys. Keep holding the keys down for about 5 seconds and the Message

Center will display Engineering Mode Menu. Press the Enter button to access the menu below:

a. Key Test (Will allow you to test all the keys to make sure they are functioning)

b. LCD Test (Tests all the display functions)

c. Functions (Press Enter to access settings and Up arrow to scroll)

i. Sleep Mode (Turn on to have the console power down automatically after 20 minutes of inactivity)

ii. Pause Mode (Turn on allow 5 minutes of pause, turn off to have the console pause indenitely)

iii. ODO Reset (Resets the odometer)

iv. Units (Sets the display to readout in English or Metric display measurements)

v. Beep (Turns off the speaker so no beeping sound is heard)

vi. Motor Test (Press Enter to run the resistance motor up and down in a continuous loop. Display shows

level setting and position sensor reading. Press stop to end test.)

vii. Safety – Off; when turned on the machine automatically goes to Level 20 of Resistance to prevent

unauthorized use by a child

viii. Unit Type (Should show Elliptical, other setting is e•Glide. Switches calorie formula, HR program settings

and watt tables for the different units)

ix. Incline On/Off (For e•Glide this is always off)

d. Security (Allows the keypad to be locked to prevent unauthorized use)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Spirit XE-295 2013 in the language / languages: English as an attachment in your email.

The manual is 3,76 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spirit XE-295 2013

Spirit XE-295 2013 User Manual - Dutch - 11 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Spirit XE-295 2013 Manual

Product: