584041
12
Zoom out
Zoom in
Previous page
1/35
Next page
XU875 & XR895
11
STEP 4: RELEASE LEVER ASSEMBLY
1. Run the Seat Recline Release Cable (58) under the Seat Back Frame (5).
2. Install the Gas Cylinder (57) into the bracket of the Seat Back Frame (5) with the 1pc of 5/16
x1-3/4 Hex Head Bolt (70), 1pc of 5/16 x 19 x 1.5T Flat Washer (76), 1pc of 5/16x 6T Nyloc
Nut (91) by using the 13/14mm Wrench (130) and 13/15mm Wrench (113). Tighten the bolt until
snug, but do not over tighten to the point of binding.
3. Remove the M6 Button Head Socket Screws holding the clamps of the left and right Release
Levers (40) by using the Allen Wrench (115). Install the 2 Release Levers (40) onto the Handle
Bar (6) just behind the hand pulse sensors. Install them at an angle that allows easy access for
use, then install and tighten the socket screws removed earlier.
4. Secure the Seat Recline Release Cable (58) and the Seat Fore/Aft Release Cable (59) on the
Handle Bar (6) by using the 4pcs of Velcro Tape. Wrap the tape around the handlebars in
places that will be under the beverage holders, when they are installed, so they are out of sight.
5. Install the Beverage Holders (38 L, 39 R) on the Handle Bar (6) with the 4pcs of 4x16m/m Self
Tapping Screws (105) by using the Phillips Head Screw Driver (114).
6. Install the Pedals (116 L, 117 R) in the Cranks by using the 13/15mm Wrench (113). Remember
that the left pedal has a reverse thread and will be screwed into the crank in the opposite
rotation from normal threads. There is an  stamped into the end of the threaded post of the
left pedal and an  in the right. Make sure to tighten the pedals as much as you possibly can.
It may be necessary to re-tighten the pedals if you feel a thumping during pedaling the bike. A
noise or feeling such as a thumping or clicking is usually caused by the pedals being too loose.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spirit XBR895 2006 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spirit XBR895 2006 in the language / languages: English as an attachment in your email.

The manual is 0,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info