583978
12
Zoom out
Zoom in
Previous page
1/39
Next page
EL3 /EL5 Elliptical
11
UNPACKING THE UNIT
1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift
Box over the unit and unpack.
2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged
parts are found, or parts are missing, contact your dealer immediately.
3. Locate the hardware package. The hardware is separated into steps. Remove the tools first.
Remove the hardware for each step as needed to avoid confusion.
STEP 1: REAR RAIL ASSEMBLY
1. Remove the hardware from the hardware pack for step 1. You should have four 3-3/4
X 3/8 bolts, four curved washers, two 2-1/4 X 3/8 bolts, two flat washers and six 5/8
X 1/4 Phillips head screws.
2. Put the two flat washers on the 2-1/4 bolts and hand-tighten them, through the top of
the middle stabilizer tube, into the rear rail assembly.
3. Put the four curved washers on the 3-3/4 bolts and hand-tighten them through the
front of the middle stabilizer tube, into the rear rail assembly.
4. Using the wrench provided tighten all six bolts securely.
5. Locate the four plastic covers (XE150, XE350 only) for the rear rail assembly and the
one cover for the front stabilizer and install them using the six 5/8 X 1/4 screws and
the Phillips head screw driver provided.
STEP 2: CONSOLE MAST ASSEMBLY
1. Remove the hardware from the hardware pack for step 2. You should have one 2-1/4 X
3/8 bolt, one lock washer, two 3/4 X 3/8 bolts, two curved washers and four 1/2 X
1/4 Phillips head screws.
2. Locate the console mast and console mast cover and slide the cover onto the mast as
far as it will go. Make sure the cover is facing the correct way.
3. At the top opening of the main body of the elliptical is a wire harness. Unravel and
straighten out the wire harness and feed it into the bottom of the console mast tube and
out of the top opening.
4. Install the console mast into the receiving bracket in the top of the main body. NOTE:
there is one bolt already installed in the receiving bracket that will engage with the slot
at the bottom of the console mast. This needs to be tightened at the end along with the
three other console mast bolts.
Assembly Instructions
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spirit EL5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spirit EL5 in the language / languages: English as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info