708113
22
Zoom out
Zoom in
Previous page
1/50
Next page
22 SPEKTRUM DX7 • TRANSMITTER INSTRUCTION MANUAL
EN
Wireless Trainer works just like the Wired Trainer, without the wire.
Select Wireless Trainer to bind a DSM2 or DSMX slave transmitter
to the master transmitter. With this option, when the master press-
es the trainer button or switch, control is given to the currently
bound slave transmitter. After binding, the slave transmitter will
remain bound to the master transmitter until a different transmitter
is bound to the master, or the slave transmitter is bound to another
receiver or a wireless master transmitter. ModelMatch™ technol-
ogy applies to the wireless trainer system; the master transmitter
will be bound to the slave in the bound model used. Also, if the
slave transmitter has ModelMatch technology, it will only be bound
to the master transmitter in the selected model during binding.
Inhibit
In Inhibit, the wireless trainer function will be inhibited
and will not function.
CAUTION: Select Inhibit in the Trainer menu when you aren’t
using the wireless trainer function. Failure to select Inhibit may
result in loss of control of the aircraft.
Programmable Master
Programmable mode enables you to program the master
transmitter to transfer any or all individual channels when you
activate the trainer switch. This mode is ideal for beginners
learning to control individual channels while the master transmitter
maintains control of all other channels. The slave transmitter
should be in Inhibit mode, if available. The Master and Slave
transmitters MUST have the same programming.
Pilot Link Master
Pilot Link Master enables you to program the master transmitter
to transfer any or all individual channels when you activate the
trainer switch. Pilot Link Master is ideal for complex models, as the
master transmitter maintains control of all secondary functions,
such as fl ight modes, retracts, fl aps and brakes.
Secondary functions can be individually assigned to the
Slave transmitter as necessary. It is not necessary to have
model programming in the slave transmitter.
DX7 Wireless Trainer Operation
1. Enter an unused model on the slave transmitter (computer
transmitter only).
2. Bind the master transmitter to the model.
3. Make sure the master and slave transmitter battery packs are
fully charged.
4. Make sure the slave transmitter is powered off.
5. Either in the Wireless Programmable Master setup page or the
Wireless Pilot Link Master setup page, select BIND. This will
put the master transmitter’s wireless trainer receiver into bind
mode. You should see the following screen:
6. Enter bind mode on the slave transmitter following the
instructions provided with that transmitter.
7. After a successful bind, the following screen should appear:
8. Press the trainer button on the master transmitter to transfer
model control from the master to the slave.
9. Release the trainer button and the master transmitter regains
control of the model.
Master Override
The Master Override feature enables the instructor to immediately
regain control of the model by moving the control sticks. After you
activate Master Override, the slave transmitter cannot control the
model until you reset the trainer switch. To reset the trainer switch:
1. Move the trainer switch to the OFF position.
2. Move the trainer switch to the ON position to activate the slave
transmitter.
SYSTEM SETUP
Wireless Trainer
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spektrum DX7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spektrum DX7 in the language / languages: English as an attachment in your email.

The manual is 4,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spektrum DX7

Spektrum DX7 User Manual - German - 49 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info