708113
21
Zoom out
Zoom in
Previous page
1/50
Next page
21SPEKTRUM DX7 • TRANSMITTER INSTRUCTION MANUAL
EN
The DX7 features a programmable trainer function with 4 wired
trainer modes, 2 wireless trainer modes and a trainer FPV mode.
The transmitter assigns the trainer function to Switch I.
The 4 wired trainer modes include:
Inhibit
In Inhibit, the slave transmitter must have the same
programming as the master transmitter (e.g., servo reversing,
travel adjust, sub-trim, trims).
Programmable Master
Programmable mode enables you to program the master
transmitter to transfer any or all individual channels when you
activate the trainer switch. This mode is ideal for beginners
learning to control individual channels while the master transmitter
maintains control of all other channels.
The slave transmitter should be in Inhibit mode, if available. The
Master and Slave transmitters MUST have the same programming.
Pilot Link Master
Pilot Link Master enables you to program the master
transmitter to transfer any or all individual channels when you
activate the trainer switch. Pilot Link Master is ideal for
complex models, as the master transmitter can maintain
control of all secondary functionsfor example fl ight modes,
retracts, aps and brakes. Secondary functions can be individually
assigned to the Slave transmitter as necessary. It is not necessary
to have model programming in the slave transmitter.
It may be necessary for the slave transmitter to be in Inhibit mode
to allow trim changes to transfer over from the master transmitter.
Slave
Use Slave mode when using the DX7 as a slave transmitter and
Pilot Link is active in the master transmitter.
DX7 Wired Trainer Operation
1. Bind the master transmitter to the model.
2. Connect the trainer cord (SPM6805) to the back of the master
transmitter.
3. Make sure the master and slave transmitter battery packs are
fully charged.
4. Make sure the slave transmitter is powered off. The slave
transmitter will power on when you connect the trainer cord.
5. Connect the trainer cord to the slave transmitter.
6. The slave transmitter screen displays information but does not
send a signal to the model.
7. Press the trainer button on the master transmitter to transfer
model control from the master to the slave.
8. While moving the trainer switch between the off and on
positions, watch for movement on the control surfaces. Adjust
the trims as necessary before fl ying.
9. Release the trainer button and the master transmitter regains
control of the model.
Master Override
The Master Override feature enables the instructor to immediately
regain control of the model by moving the control sticks. After you
activate Master Override, the slave transmitter cannot control the
model until you reset the trainer switch. To reset the trainer switch:
1. Move the trainer switch to the OFF position.
2. Move the trainer switch to the ON position to activate the slave
transmitter.
SYSTEM SETUP
TRAINER
Wired Trainer
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spektrum DX7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spektrum DX7 in the language / languages: English as an attachment in your email.

The manual is 4,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spektrum DX7

Spektrum DX7 User Manual - German - 49 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info