726853

Spektrum DX18 - SPM18000 Manual

10
Zoom out
Zoom in
Previous page
1/42
Next page
10 SPEKTRUM DX18 • TRANSMITTER INSTRUCTION MANUAL
EN
PROGRAMMING FAILSAFE POSITIONS
You establish failsafe positions when you bind your transmitter and receiver. If radio signal connection is lost between the transmitter
and receiver, the receiver immediately moves the aircraft control surfaces to the failsafe positions. The Spektrum AR9020 receiver
has three failsafes programming options: SmartSafe, Hold Last Command, and Preset.
If you assign the receiver THRO channel to a transmitter channel other than throttle , we recommend using Preset failsafe with the
throttle in the low position.
NOTICE: Failsafe features vary according to receiver. Always consult the receiver instruction manual for failsafe features.
Before fl ight, ALWAYS confi rm the failsafe functions as you would expect.
SmartSafe Failsafe
SmartSafe is a failsafe acting only on the throttle channel that
offers the following benefi ts:
• Prevents electric motors from operating when the receiver
power is on and the transmitter power is off.
• Prevents the speed controller from arming until the throttle is
moved to the low throttle position.
• Powers off an electric motor and reduces gas/glow engines
to idle if signal is lost.
To Program SmartSafe, move the throttle to the low or off posi-
tion before putting the transmitter in bind mode.
To Test the SmartSafe
1. Power the transmitter and receiver on.
2. Power off the transmitter. The throttle should immediately
move to the failsafe position.
CAUTION: Make sure the aircraft is restrained on the
ground. If failsafe is not set, your aircraft might advance to mid
or full throttle.
Hold Last Command
The Hold Last Command failsafe maintains the last command
on all channels except throttle; if radio signal is lost, the aircraft
maintains the commanded heading until the receiver regains
signal.
To program Hold Last Command, follow the provided binding
instructions in this instruction manual.
To Test Hold Last Command
1. Power on the transmitter and receiver.
2. Move one of the control sticks and hold the input.
3. While holding the control input, for example, a small amount
of rudder, power off the transmitter. The rudder should
maintain the input command.
CAUTION: Make sure the aircraft is restrained on the
ground. If the failsafe does not function as you would expect, the
aircraft throttle might advance to mid or full throttle.
Preset Failsafe
The Preset failsafe moves all channels to their programmed
failsafe positions.
We recommend using Preset failsafe to deploy spoilers on
sailplanes to prevent a fl yaway if radio signal is lost.
To program Preset failsafe:
1. Insert the bind plug in the bind port on the receiver and
power on the receiver.
2. Remove the bind plug when the orange LED on the main
receiver and all attached remote receivers fl ash rapidly. The
orange receiver LEDs continue fl ashing.
3. Move the transmitter control sticks and switches to the
desired Preset failsafe position. Power the transmitter on.
4. Failsafe programming is complete when the orange LEDs on
the transmitter and all receivers are on solid.
CAUTION: Make sure the aircraft is restrained on the
ground. If the failsafe does not function as you would
expect, the aircraft throttle might advance to mid or full throttle.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spektrum DX18 - SPM18000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spektrum DX18 - SPM18000 in the language / languages: English as an attachment in your email.

The manual is 2,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spektrum DX18 - SPM18000

Spektrum DX18 - SPM18000 User Manual - German - 39 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info