744234
41
Zoom out
Zoom in
Previous page
1/53
Next page
GB
GB 41
M H2O, and this unavoidably results in deposits on the surfaces of the heat
exchanger, these surfaces must be cleaned with the provided brush on a regular
basis.
The water heat exchanger is cleaned through the cleaning opening. To do this,
open the upper cladding door and remove the cap by removing the wing nuts.
Now the heat exchanger surfaces are exposed and can be cleaned with the
supplied cleaning brush.
The assembly occurs in the reverse order: First put the cap on the cleaning
opening and re-attach the wing nuts.
Piko H2O
Because the water heat exchanger directly cools down the flue gases of the
Piko H2O, and this unavoidably results in deposits on the surfaces of the
heat exchanger, these surfaces must be cleaned with the provided brush
on a regular basis.
The operating handle of the cleaning mechanism is included in delivery and
must be inserted in the 20mm hole on the top left side of the unit when
cleaning. After inserting it, it must be twisted about 5 times to the right and
left to the stops (approximately 20°angle of rotation).
A = remove wing nuts, remove
cleaning cover
B = remove deposits in the pipes
und on the surfaces!
View from front
6.5 DOOR MECHANISM SENSO S RLU
The locking mechanism, in particular the spring force of the closing mecha-
nism, is preset at the factory so that the door closes ideally.
If it is necessary to increase the closing force (door does not close automat-
ically), proceed as follows:
To access the door mechanism, it is necessary to open the bottom inspection
flap (Fig. 29). After opening it, the closing mechanism is visible on the hinge
side of the fire door.
To tighten the mechanism, close the fire door and put a hexagon wrench
(wrench size 24) on the key adapter (1) the drive shaft
Now turn the drive shaft to the left to increase the spring force (Fig. 30).
This should be done in small increments (without gear travel). Then check
the function of the door mechanism. Optimum locking function is guaranteed
if the catch on door wing locks into place and the door closes flush against
the body.
Fig. 29 Fig. 30
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spartherm Stovo S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spartherm Stovo S in the language / languages: English as an attachment in your email.

The manual is 3.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spartherm Stovo S

Spartherm Stovo S User Manual - German - 52 pages

Spartherm Stovo S User Manual - Dutch - 53 pages

Spartherm Stovo S User Manual - Dutch - 53 pages

Spartherm Stovo S User Manual - Dutch - 44 pages

Spartherm Stovo S User Manual - French - 53 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info