Manual Spartherm Passo (page 30 of 53) (English)

744243

Zoom out

Zoom in

1/53

GB 30

protocol“ on page 52). When first putting your appliance into service, only

start a moderate fire. This enables you to avoid cracks in the combustion

chamber covering (which may still contain residual humidity before the first

firing). Slowly increase the heating power to about 30% above nominal heat

output by setting the fire 3 to 5 times to give the corrosion coating applied

to the surfaces time to 'burn in' properly The paint can be slightly soft

during this process, please do not place any objects on the stove and do

not touch your device. During this burning-in process, an unpleasant odor

(sometimes accompanied by the build-up of smoke) may appear. Ensure the

provision of good room ventilation for this burn-in process. Open all doors

and windows to the outside of the building.

Initial commissioning of Senso M H2O / Piko H2O

The initial commissioning must only be executed after all necessary com-

ponents are connected and all necessary safety devices are integrated

and functional, the water heat exchanger is filled and the system has been

ventilated. Operation without water, when only partially filled or when safety

devices are not functioning is not permitted! During initial commissioning

of the water heat exchanger, it may be necessary to vent this several times.

Moreover, the owner must be instructed in detail concerning the operation,

function and maintenance of the overall system, including all supplemental

components. In addition, the measures for maintaining safe operation of the

system must be communicated to the owner. The executed instruction must

be documented in the commissioning protocol (see „10. Commissioning

protocol“ on page 52.). The installation and operating instructions must

always be kept in the vicinity of the Senso M H2O / Piko H2O where they can

be easily accessed.

Contaminated condensate exiting the combustion chamber liner may con-

taminate/damage the base unit. Here an absorbent pad should be placed

under the unit for the first burn-ups until condensate no longer emerges.

Before commissioning, check to ensure there are no objects in the combus-

tion chamber/in the ash drawer. These must be removed.

During heating and cooling, metallic grinding noises may be heard as the

components of your stove expand or contract. These are completely normal

and arise as a result of material expansion caused by the high temperatures.

4.1.1 COMBUSTION AIR REGULATION

Combustion air is regulated across an infinitely variable range using the

actuating lever located under the door. Adjustment takes place with the fire

door closed!

Air supply opened (A): For heating-up or for adding more firewood, move

the actuating lever fully to the right. The combustion chamber will now be

supplied with the maximum amount of air for primary and for secondary

combustion purposes.

Throttled combustion (B): leave the setting lever in a near-central position.

The primary combustion air supply is now closed, ensuring that the fire is

not supplied with too much air. Secondary air is diverted across the ceramic

viewing glass to prevent it from sooting up. This is the default position while

a fire is burning. The precise position

depends on local conditions and can be

adjusted by the operator to reflect the

combustion characteristics of the stove.

Air flow closed (C): actuating lever at

far left. The combustion chamber of the

stove receives no combustion air in this

setting. However, do not shut down the

air supply altogether until the fuel has

burned away completely. If the fireplace

is not in operation, you should always

close the air supply.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Spartherm Passo in the language / languages: English as an attachment in your email.

The manual is 3.7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spartherm Passo

Spartherm Passo User Manual - German - 52 pages

Spartherm Passo User Manual - Dutch - 53 pages

Spartherm Passo User Manual - Dutch - 44 pages

Spartherm Passo User Manual - French - 53 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Spartherm Passo Manual

Product: