Manual Sparky BP 750CE (page 10 of 114) (English, German, French, Italian, Polish, Portuguese, Spanish)

604120

Zoom out

Zoom in

1/114

BP 750CE

- Impact drilling - for drilling masonry, concrete,

etc.

- Hammer mode - for chiselling and demolition.

For operation without fatigue during chiselling

and demolition, the accessory can be tted and

xed (at intervals of 8 degrees) in the desired

angular position (see “Changing the chisel posi-

tion”).

Turn the operation mode switch 6 to the desired

position:

(1) - Impact drilling

(2) - Changing the chisel position

(3) - Hammer mode

INSERTING OF SDS-MAX TOOL

Clean and grease the shank of the accessory,

before placing it into the socket!

Keep the locking socket 2 in upper (front) posi-

tion while inserting the tool.

Place the tool into the spindle without effort.

Rotate the tool until the grooves coincide.

After the grooves have coincided, push the tool

down (until the xing mechanism produces an

audible “click”). Check the proper xing of the

tool by pulling it strongly outwards.

WARNING: For operating with chisels

switch 6 shall always be in “hammer” posi-

tion.

REMOVING THE SDS-MAX TOOL

Pull the locking clutch entirely back and take the

tool out.

CHANGING THE CHISEL POSITION

- Insert the tool in the socket as it is described in

point “Inserting the SDS-max tool”.

- Turn the operating mode switch 6 in position

“Changing the chisel position”.

- Turn the tool by hand to the desired position.

- Turn the operating mode switch 6 in position

“hammer”, and then turn the tool slightly left wise

and right wise until it is locked.

Longer operation life of the rotary hammer and

higher efciency can be achieved only with well-

sharpened tools for demolition and chiselling.

AUXILIARY HANDLE

Always use the auxiliary handle.

Loosen the handle by turning it left wise. Turn

the handle in the most convenient for operation

position, and then tighten it well.

Do not carry the machine by a loose auxiliary

handle.

You can x the drilling depth through depth

gauge 4. The depth gauge 4 can be xed by

screw 3.

The auxiliary handle for these models is con-

nected to the body of the machine through vi-

bration dampers, protecting the operator and

reducing fatigue.

RECOMMENDATIONS FOR

OPERATION

Apply moderate pressure during operation (ap-

proximately 150-200 N)! Higher pressure will not

increase efciency when drilling and chiselling,

but it will lead to decreasing the operation life of

the machine.

Take the drill bit out of the opening from time to

time to remove dust.

Watch out for the stage of bit blunting and re-

place the bit when considerable decrease of ef-

ciency is observed.

ACCESSORIES

▪ SDS-max twist drill bits for concrete Ø12 to

Ø50 mm. We recommend operation with Ø24

to Ø40 drill bits, for the optimum operation the

machine is designed for.

▪ SDS-max break through drill bits for concrete

up to Ø80 mm

▪ SDS-max core cutters up to Ø100 mm

▪ SDS-max point chisels up to 600 mm long

▪ SDS-max at chisels up to 80 mm wide

▪ SDS-max groove chisel up to 32 mm wide

WARNING: We recommend using

these accessories or attachments when op-

erating your power tool. The use of any other

accessories or attachments might present a

risk of injury. Only use accessory or attach-

ment for its stated purpose. If you need any

assistance for more details regarding these

accessories, ask your local SPARKY service

centre.

VII - Maintenance

WARNING: Always ensure that the

tool is switched off and unplugged before

attempting to perform inspection or mainte-

nance.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sparky BP 750CE in the language / languages: English, German, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sparky BP 750CE Manual

Product: