604120
9
Zoom out
Zoom in
Previous page
1/114
Next page
7
Original instructions
EN
This power tool is equipped with a
mechanism for reducing vibrations, decreasing
them by more than 30%.
PRIOR TO INITIAL OPERATION
Make sure the power supply voltage corre-
sponds to the value indicated on the name
plate with technical data of the tool.
Always check the position of ON/OFF switch.
The power tool must be connected to the
power supply socket only when this switch is
in OFF position. If the plug is connected to
a receptacle while the power switch is in the
ON position, the power tool will start operat-
ing immediately, which could cause a serious
accident.
Make sure that the cord and the plug are in
order. If the replacement of the supply cord is
necessary, this has to be done by the manu-
facturer or his agent in order to avoid a safety
hazard.
WARNING: Always switch off and un-
plug the power tool prior to any adjustment,
servicing or maintenance.
In case the work area is remote from the pow-
er source, use as short as practicable exten-
sion cord with proper cross-section.
Check that the auxiliary handle is properly
mounted and reliably tightened.
SWITCHING ON - SWITCHING OFF
Switching on: Push and hold down switch 7.
Switching off: Release switch 7.
At low temperatures, demolishing with the pow-
er tool must begin only after it was operated for
about 3 minutes at no-load mode.
WARNING: Upon overloading the ma-
chine with 30% the red light-emitting diode 10
will glow. The machine must not be operated
conti nuously in this mode.
SELECTING THE SPEED, FREQUENCY
AND IMPACT ENERGY
Rotate the regulator 8 to choose a position
appropriate for the processed material. The
constant electronics maintain the speed, the
frequency and the impact energy constant, in-
dependently of the load, thus ensuring steady
operation mode. It is recommended to use the
operation modes listed in the table.
Rotate the regulator 8 from position A to position
F to increase the speed, the frequency and the
impact energy. The indicator 9 shall blink with
green light.
To choose High Power mode, rotate the regula-
tor 8 to position G. This mode is specied by in-
creased impact energy up to 13 J. The indicator
9 shall glow with constant green light.
WARNING: Using High Power mode
is recommen ded only when chiselling (ham-
mer mode), and for brief operation in impact
drilling mode. Continuous operation in impact
drilling mode shall result in operator’s quick
fatigue and increased wear-out of the ma-
chine.
SELECTING THE OPERATION MODE
The switching of operation modes can be per-
formed when the machine is not operating.
This rotary hammer can be used in two opera-
tion modes:
Application
Regulator
position
Rotation
speed
Impact rate
Single impact
energy
Render / Light construction
materials
A-B 120-145 min
-1
1150-1450 min
-1
4-5 J
Chiselling tiles C 175 min
-1
1700 min
-1
7 J
Bricks D 200 min
-1
1950 min
-1
8 J
Drilling in concrete E-F 225-250 min
-1
9-10 J
Chiselling concrete G 2800 min
-1
13 J
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sparky BP 750CE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sparky BP 750CE in the language / languages: English, German, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info