Manual Sparky BP 330E (page 10 of 110) (English, German, French, Italian, Polish, Portuguese, Spanish)

604122

Zoom out

Zoom in

1/110

BP 330E

SELECTING THE OPERATION MODE

The switching of operation modes can be per-

formed when the machine is not operating.

Rotate the operation mode switch 4 in the direc-

tion marked on the switch to the desired position

to choose:

(1) Impact drilling (Fig.6) - for drilling masonry,

concrete, etc.

(2) Hammer mode (Fig.7) - for chiselling and

demoliting.

(3) Adjusting the chisel position (Fig.8) to x

the chisel in the desired angular position for

demoliting and chiselling (see “Adjusting the

chisel position”).

WARNING: Turn the operation mode

selector switch only in the direction marked

on the switch. During each switching between

operation modes turn the tool slightly by hand

leftwise and rightwise until it is locked.

In impact drilling mode the rotary hammer

equipped with adapter and chuck 176838 (not

included) can be used as a drill for drilling in

steel, wood, plastics, etc.

ADJUSTING THE CHISEL POSITION

(Fig.9)

- Insert the tool into the socket as it is described

in section “Inserting the SDS-Plus tool”.

- Turn the operating mode switch 4 in position

“Adjusting the chisel position”.

- Rotate the tool by hand to the desired posi-

tion.

- Turn the operating mode switch 4 to position

“hammer”, and then turn the tool slightly by hand

leftwise and rightwise until it is locked.

Longer operation life of the rotary hammer and

higher efciency can be achieved only with well-

sharpened tools for demoliting and chiselling.

AUXILIARY HANDLE

Always use the auxiliary handle.

Loosen the handle by turning it leftwise. Turn the

handle in the most convenient for operation po-

sition, and then tighten it well.

Do not carry the machine by a loose auxiliary

handle.

You can x the drilling depth through depth

gauge 8. The depth gauge 8 can be xed by

screw 9.

RECOMMENDATIONS FOR

OPERATION

Apply moderate pressure during operation (ap-

proximately 50-80 N)! Higher pressure will not

increase efciency when drilling and chiselling,

but it will lead to decreasing the operation life of

the machine.

Take the drill bit out of the opening from time to

time to remove dust.

Watch out for the stage of bit blunting and re-

place the bit when considerable decrease of ef-

ciency is observed.

The optimum capacity when drilling in concrete

is up to 24 mm, and the possible capacity is up

to 30 mm.

ACCESSORIES

▪ SDS-Plus drill bits for concrete Ø6 mm to

Ø24 mm;

▪ SDS-Plus core cutters up to Ø80 mm;

▪ SDS-Plus point chisels up to 300 mm long;

▪ SDS-Plus at chisels up to 40 mm wide.

WARNING: We recommend using

these accessories or attachments when op-

erating your power tool. The use of any other

accessories or attachments might present a

risk of injury. Only use accessory or attach-

ment for its stated purpose. If you need any

assistance for more details regarding these

accessories, ask your local SPARKY service

centre.

VII - Maintenance

WARNING: Always ensure that the

tool is switched off and unplugged before

attempting to perform inspection or mainte-

nance.

GENERAL INSPECTION

Regularly inspect all fasteners and ensure they

are properly tightened. Should any of the screws

be loose, retighten it immediately to avoid haz-

ards. (Fig. 10)

If the replacement of the supply cord is neces-

sary, this has to be done by the manufacturer or

his agent in order to avoid a safety hazard.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sparky BP 330E in the language / languages: English, German, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sparky BP 330E Manual

Product: