604122

Sparky BP 330E Manual

9
Zoom out
Zoom in
Previous page
1/110
Next page
7
Original instructions
EN
breaking and chiselling in brickwork, concrete
and rocks with high efciency. In impact drilling
mode the rotary hammer equipped with adapter
and chuck 176838 (not included) can be used
as a drill for drilling in steel, wood, plastics, etc.
Power tools marked with this symbol
are equipped with a mechanism for reducing vi-
brations, decreasing them by more than 50%.
PRIOR TO INITIAL OPERATION
▪ Make sure the power supply voltage corre-
sponds to the value indicated on the name
plate with technical data of the tool.
▪ Always check the position of ON/OFF switch.
The power tool must be connected to the
power supply socket only when this switch is
in OFF position. If the plug is connected to
a receptacle while the power switch is in the
ON position, the power tool will start operat-
ing immediately, which could cause a serious
accident.
▪ Make sure that the cord and the plug are in or-
der. If the replacement of the supply cord is nec-
essary, this has to be done by the manufacturer
or his agent in order to avoid a safety hazard.
▪ In case the work area is remote from the power
source, use as short as practicable extension
cord with proper cross-section.
WARNING: Always switch off and un-
plug the power tool prior to any adjustment,
servicing or maintenance.
▪ Check that the auxiliary handle is properly
mounted and reliably tightened.
SWITCHING ON - SWITCHING OFF
Brief activation
Switching on: Press ON/OFF switch 5. (Fig.1)
Switching off: Release ON/OFF switch 5.
Continuous operation
Switching on: Press ON/OFF switch 5 and in
pressed position lock it by button 6. (Fig. 2)
Switching off: Press ON/OFF switch 5 once and
release it immediately.
At low temperatures, demolishing with the pow-
er tool must begin only after it was operated for
about 3 minutes at no-load mode.
INSERTING OF SDS-Plus TOOL
Clean and grease the shank of the accessory,
before placing it into the socket! (Fig.3)
Pull backward the sleeve 3 of the socket 1
(Fig. 4a) and insert the SDS-Plus bit until stop.
Ensure that the socket grooves correspond to
the shank channels, and then release the sleeve
to x the bit. (Fig. 4b)
To remove the bit, pull the sleeve 3 back, and
then take the bit out. (Fig.5)
WARNING: Never use drill bits with
diameter exceeding the indicated to avoid
overloading the power tool..
SELECTINGTHESPEED,FREQUENCY
AND IMPACT ENERGY
Rotate the regulator 7 to choose a position ap-
propriate for the processed material. It is recom-
mended to use the operation modes listed in the
table.
Application
Regulator
position
Rotation
speed
Impactrate Impactenergy
Boring with core cutters A-D 380-650 min
-1
1560-2660 min
-1
1.5-3.6 J
Render / Light construction
materials / Bricks / Chiselling
tiles
D-Е 650-740 min
-1
2660-3030 min
-1
3.6-4.3 J
Chiselling and drilling concrete
F 830 min
-1
3400 min
-1
5 J
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sparky BP 330E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sparky BP 330E in the language / languages: English, German, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info