611458
104
Zoom out
Zoom in
Previous page
1/202
Next page
Vi3000 USER MANUAL
®
11.1 11.1: SOLO > PRIMARY BEHAVIOUR
11.0: SOLO System
AFL, PFL and SIP
The solo system on the Soundcraft Vi3000™ comprises a non-destructive PFL and AFL Solo capability from Inputs
and Outputs, and also the option of a destructive Solo-In-Place mode, for use only during soundchecks or rehearsals.
Solo-In-Place mode has to be enabled from within the Monitor Setup and changes the mode of operation of the Solo
System. It is automatically cancelled if the Monitor Setup screen is closed, to ensure that it cannot accidently be left
on.
PFL and AFL Soloing (SIP Mode OFF)
• Soloing a single Input locally generates a PFL or AFL Solo onto the Solo Bus, depending on the mode selected in the
Monitor Setup page (default is AUTO, see next point).
• If the Input Solo Mode is set to AUTO in the Monitor Setup page, soloing more than one Input locally (by pressing
and holding the rst Solo/Sel switch then pressing others, or switching off AUTO CANCEL mode) will generate an AFL
Solo onto the Solo Bus from all soloed Inputs. If a single output is soloed, the solo will be PFL.
• The PFL feed from Mono Inputs is taken after the channel Pan control so the signal heard on the Monitor outs will
reect the Pan setting. If the Input is a Stereo Input, the PFL feed is left channel to left Solo Bus, right to right.
• The AFL feed from Mono or stereo (paired) Inputs is stereo and follows the channel Pan.
• Soloing an Output (either locally or via a VCA Master Solo) generates an AFL or PFL Solo, depending on the mode
selected in Monitor Setup (default is AFL for outputs).
The post-fade Output signal is switched onto the Solo Bus.
• In all cases when SIP Mode is OFF, operation of any Solo will switch the audio onto the Solo Bus and the Monitor
section will be automatically switched so that the Solo audio replaces the previous monitor source selection (if any)
assuming that IN Solo and/or OUT Solo have been selected as a Monitor Source in the Monitor Setup Page.
Solo-In-Place Soloing (SIP mode ON)
• Soloing an Input generates a ‘destructive’ SIP Solo, actually muting or dimming all other Inputs which are not Soloed
or set to Mute Safe, as if you had pressed their channel ON switches. Other channels which are subsequently soloed
will be unmuted. The amount of dimming is controlled by the SOLO BLEND control on the front panel.
• Soloing an Input (or group of Inputs) by soloing a VCA Master that the input is assigned to, generates a SIP Solo on
all Inputs in the VCA Group.
* The Input signal is not switched onto the Solo Bus, and the Monitor section does not switch the Solo Bus audio to
override the monitor source selection (you hear the soloed signal(s) via the Master LRC busses directly.
• Soloing an Output generates a normal Output AFL or PFL Solo (according to the mode selection made in Monitor
Setup), the same as if SIP Mode was OFF. The Output signal is switched onto the Solo Bus and the Monitor section
switches so that the Output
Solo audio is heard on the Monitors, replacing the previous monitor source, if any.
SOLO SYSTEM BEHAVIOUR
104


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft Vi 3000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft Vi 3000 in the language / languages: English as an attachment in your email.

The manual is 17,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info