611465

Soundcraft Signature 10 Manual

19
Zoom out
Zoom in
Previous page
1/55
Next page
10, 12, 12MTK User Manual
3.1: INTRO TO I/O
INPUTS & OUTPUTS > INTRODUCTION TO I/O
3.1: INTRODUCTION TO I/O
The Signature console offers a choice of industry standard audio inputs and outputs. All Jack and XLR
inputs are balanced. Below are some terms used in this manual and on the console labelling that may
be of use to you.
AUX (Auxiliary) Output
An output bus made up of the summed Aux
contributions from input channels. In other
words, the AUX1 output will be a mix of all input
channel signals, with levels controlled by the
AUX1 controls on the individual input channels.
Auxiliary mixes are used for many purposes -
alternative mixes for monitoring, processing by
external FX units, and more.
Balanced
A ‘Balanced’ signal (Balanced Line) is one where
the signal is split between two conductors with
the same impedance / impedance to ground.
At a differential input, the differences between
thetwoconductorsareamplied,soanynoise
aquired between output and input is rejected
(common-mode rejection).
GRP (Group)
An output bus made up of the summed
contributions from any inputs routed to the
Group. For example, on the Signature 12 and
12MTK consoles (Groups not available on
Signature 10), all inputs with their 1-2 buttons
pressed will be added to the Group 1 and 2
mixes. The pan / balance control determines how
the signal is proportioned between the Group 1
and Group 2 busses (Group 1 left, and Group 2
right).
Hi-Z
High Impedance. Guitar pick-ups generally have
‘high impedance’ outputs and therefore require
asignicantlyhigherthanusualinputimped-
ance when plugging them directly into a console
(straight from the guitar plug - not via an amp
or a microphone). Hi-Z Inputs provide this. On
the Signature console selected inputs have Hi-Z
input switches to accomodate Hi-Z sources.
Jack
This is the long, quarter-inch connection most
commonly used on the signature console for
line level inputs and outputs such as keyboards,
external FX processors, playback and recording
devices, and so on. All Signature-series Jack
sockets are ‘Tip-Ring-Sleeve’ 3-pole types. Jack
outputs are impedance balanced.
Line
For inputs and outputs this refers to a line level
signal. This is a higher voltage signal than ‘mic
level’.
Mic
Microphone. For inputs and outputs this refers to
a mic level input. This is a lower voltage signal
than ‘line level’.
MST (Master)
Master Stereo Output: The main stereo Group
output made up of the summed contributions
from any inputs routed to ‘MST’ with their ‘MST’
buttons.
RCA
The small line-level connector commonly found
on consumer playback equipment. RCA inputs
are provided for the 9/10 (Signature 10) and
11/12 (Signature 12 / 12MTK) stereo input
channels (Playback Channels).
USB - Universal Serial Bus
Standard serial data connection used by the
Signature console for sending and receiving
digital audio streams.
XLR
The round, three-pin connections. On the
Signature console they are used for microphone
inputs and the main stereo outputs.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft Signature 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft Signature 10 in the language / languages: English as an attachment in your email.

The manual is 6,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Soundcraft Signature 10

Soundcraft Signature 10 User Manual - German - 54 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info