611465

Soundcraft Signature 10 Manual

55
Zoom out
Zoom in
Previous page
1/55
Next page
10, 12, 12MTK User Manual
APPENDIX 1: NO SOUND?
NO SOUND
APPENDIX 1: NO SOUND?
A Troubleshooting Guide.
Isaninputfailingtoappearatappearingatanoutput?Thebestapproachitistorstmakesurethe
inputisvalid,andthenworkthroughthesignalpathtondoutwherethe‘break’is...Checktheexact
audio path of any signal by referring to the signal path diagrams in Chapter 4.
Check Solos
If a PFL light on an input channel is lit, or the AFL/PFL ACTIVE LED (below main audio meter) then a solo is active
and all channels except those that are ‘soloed’ will be muted. This will only affect the headphones output.
Clear all active Solos by pressing any illuminated Input Channel PFL buttons and any engaged Aux Master AFL buttons.
Check Input Channel Path To Solo Bus
The channel solo can be very useful here. If you Solo the channel it will send a post-EQ, pre-Mute signal to the Solo
bus and you should be able to see signal indicated on the main meters, or hear it in the headphones.
Things that might prevent the signal getting that far include a GAIN control set too low, phantom power not switched
on for a source that requires it (condenser microphone, active DI etc), or an active SUB RTN switch on a channel
where there is no USB input (MTK models only).
Check the Input Channel routing diagram (Section 4.1) and ensure the channel controls are set up correctly.
Check Input Channel Path To Routing
If the signal is present on the Solo bus with PFL engaged, the problem might be further down the input channel. It
could be simply that the Mute is active, or the fader is down - or there could be a problem with the routing.
For a signal to go to the Main Stereo Bus or to a Group Bus, the corresponding routing switch must be engaged
(MST,1-2,or3-4).Also,apanorbalancecontrolcanhaveasignicanteffect-ifthesignalisroutedtoGroups1-2,
for example, and the pan control is full left (Group 1), you won’t hear anything from the Group 2 bus.
Check Mute and fader status, and that the channel routing selections are correct.
Check Bus Masters
If you have routed signal to the Main Stereo bus or a Group bus, or you have turned up the channel’s contribution
to an Aux bus, then the master controls for that bus must be set correctly. For example, if the signal is routed to the
Stereo master but the Stereo Master fader is down, you won’t hear anything.
Check the controls on any Bus Masters that the signal is routed to.
No FX?
For an internal FX to be heard, there must be a source contribution from a valid input. Increase the level to the FX
bus using the Aux/FX control. Also, the signal is return through the corresponding FX Return Channel. Troubleshoot
this signal path as you would do for a normal input channel.
The internal FX routing has three stages - send, processor, and return. All three must be set correctly for the FX to be heard.
… 55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft Signature 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft Signature 10 in the language / languages: English as an attachment in your email.

The manual is 6,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Soundcraft Signature 10

Soundcraft Signature 10 User Manual - German - 54 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info