611474
45
Zoom out
Zoom in
Previous page
1/60
Next page
43Soundcraft MFXi MPMi User Guide Issue 1210
• Repeat this procedure on other channels as required. As more channels
are added to the mix, the meters may move into the red section. Adjust the
overall level using the Master Faders if necessary.
• Listen carefully for the characteristic sound of “feedback”. If you cannot
achieve satisfactory input level setting without feedback, check microphone
and speaker placement and repeat the exercise. If feedback persists, it may
be necessary to use a Graphic Equaliser to reduce the system response at
particular resonant frequencies.
Note:
The initial settings should only be regarded as a starting point for your mix. It is
important to remember that many factors affect the sound during a live performance,
for instance the size of the audience!
You are now ready to start building the mix and this should be done progressively,
listening carefully for each component in the mix and watching the meters for any
hint of overload. If this occurs, back off the appropriate Channel Fader slightly until
the level is out of the red segments, or adjust the Master Faders.
Remember that the mixer is a mixer, not an amplier. Increasing the overall level
is the job of the amplier, and if it is impossible to provide adequate level, it is
probable that the amplier is too small for the application. Choose your amplier
carefully, and do not try to compensate for lack of power by using the mixer to
increase output level.
Note:
The level of any source signal in the nal output is affected by many factors, prin-
cipally the Input Gain control, Channel Fader and Mix Faders. You should try to use
only as much microphone gain as required to achieve a good balance between
signals, with the faders set as described above.
If the input gain is set too high, the channel fader will need to be pulled down too far
in compensation to leave enough travel for successful mixing and there is a greater
risk of feedback because small fader movements will have a very signicant effect
on output level. Also there will be a chance of distortion as the signal overloads
the channel and causes clipping.
If the gain is set too low, you will not nd enough gain on the faders to bring the
signal up to an adequate level, and backgound hiss will be more noticeable.
This is illustrated below:
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft MPMi at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft MPMi in the language / languages: English as an attachment in your email.

The manual is 2,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Soundcraft MPMi

Soundcraft MPMi User Manual - German - 35 pages

Soundcraft MPMi User Manual - French - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info