611474
35
Zoom out
Zoom in
Previous page
1/60
Next page
33Soundcraft MFXi MPMi User Guide Issue 1210
Lexicon® FX PROCESSOR OVERVIEW
The effects within the console have been designed with both live sound reinforcement and home recording in
mind. Featuring the deep, rich reverb algorithms that Lexicon® are renowned for the effects processor offers
increased versatility and high quality effects, all instantly accessible via the extremely intuitive front panel
controls. The effects processor has 32 programs which are held in two banks of 16 programs which can be
stored to allow you to create your own custom effect settings.
Front panel controls include a Program Select knob, Tempo and Store buttons, and three independent
Parameter knobs that provide instant access and control over the most critical parameters for the selected
effect. The table on page 40 lists the functions of the Parameter knobs for each fx program.
Note: When the console is powered up the program recalled will always be the selected program in BANK A.
FX OPERATION
Select and Load a Program
Turn the Program Select knob to choose a program. Note that the console has 32 programs which are held
in two banks of 16 programs. There are individual BANK A and BANK B LED’s to indicate which bank is cur-
rently active. When turning the rotary Program Select knob through 360 degrees (a full rotation) the selected
bank will alternate between BANK A and BANK B.
Set Audio Levels
1. Set the gain on the input channel appropriate to the source (vocal microphone, guitar, keyboard, etc.).
2. Set the FX send on the input channel to the 2 o’clock position.
3. Set the FX Master level to the 2 o’clock position. Set the EFFECTS Fader on the FX section to the fully
down position.
4. Provide source signal (by speaking or singing into the microphone, playing guitar, keyboard, etc.) on the
selected channel.
5. Turn up the FX Send level on the channel until the Red CLIP LED in the FX Panel lights only occasionally.
If the red Input LED stays lit, too much signal is being sent to the effect processor; reduce the FX Master or
the FX Send on the input channel.
6. Raise the EFFECTS Fader towards the 0dB position to feed the required level of FX Processor output signal
to the mix.
7. To increase or decrease the amount of effect on the signal, adjust the FX Send level on the channel that
you want affected.
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft MPMi at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft MPMi in the language / languages: English as an attachment in your email.

The manual is 2,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Soundcraft MPMi

Soundcraft MPMi User Manual - German - 35 pages

Soundcraft MPMi User Manual - French - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info