611456

Soundcraft MFX20 Manual

18
Zoom out
Zoom in
Previous page
1/48
Next page
18
STEREO INPUT CHANNELS
1 INPUTS STEREO 1/2
These inputs accept 3-pole 6.35mm (1/4") jacks. Use these inputs for sources
such as keyboards, drum machines, synths, tape machines or processing units. The
inputs are BALANCED for low noise and top quality from professional equipment,
but you can use UNBALANCED sources by wiring up the jacks as shown in the
‘Wiring Up’ section earlier in this manual, although you should then keep cable
lengths as short as possible. Mono sources may be used by plugging into the left
jack only.
2 GAIN
The GAIN control sets the level of the channel signal.
3 EQUALISER
HF EQ
Turn to the right to boost high (treble) frequencies, adding crispness to percussion
from drum machines, synths and electronic instruments. Turn to the left to cut these
frequencies, reducing hiss or excessive brilliance. Set the knob in the centre-detented
position when not required. The control has a shelving response giving 15dB of
boost or cut at 12kHz.
MF EQ
Turn to the right to boost mid frequencies by up to 15dB, turn to the left to cut these
frequencies by up to 15dB. The centre frquency of the MF EQ is 720Hz.
LF EQ
Turn to the right to boost low (bass) frequencies, adding extra punch to synths,
guitars and drums. Turn to the left to reduce hum, boominess or improve a mushy
sound. Set the knob to the centre-detented position when not required. The control
has a shelving response giving 15dB of boost or cut at 80Hz.
4 AUX SENDS
These are used to set up a separate mixes for FOLDBACK, EFFECTS or recording, and
the combination of each Aux Send is mixed to the respective Aux Output at the rear
of the mixer. For Effects it is useful for the signal to fade up and down with the fader
(this is called POST-FADE), but for Foldback or Monitor feeds it is important for the
send to be independent of the fader (this is called PRE-FADE).
AUX SENDS 1 and 2 are both globally switchable between pre and post-fade (see
master section on page 23). The send pots are fed with a mono sum of the L & R
signals. Aux 3 is always post-fade.
5 FX SEND
This control sets the level of the post-fade signal being sent to the FX bus; from there
it is routed to the FX processor. The FX Send is always post-fader.
6 BALANCE
This control sets the amount of the channel signal feeding the Left and Right MIX
buses, allowing you to balance the source in the stereo image. When the control is
turned fully right or left you feed only that side of the signal to the mix. Unity gain is
provided by the control in the centre-detented position.
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft MFX20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft MFX20 in the language / languages: English as an attachment in your email.

The manual is 2,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info