611456

Soundcraft MFX20 Manual

16
Zoom out
Zoom in
Previous page
1/48
Next page
16
The Send may also be tapped off as an alternative pre-fade, pre-EQ direct output if
required, using a lead with tip and ring shorted together so that the signal path is
not interrupted (see below).
5 Gain
This knob sets how much of the source signal is sent to the rest of the mixer. Too
high, and the signal will distort as it overloads the channel. Too low, and the level of
any background hiss will be more noticeable and you may not be able to get enough
signal level to the output of the mixer.
Note that some sound equipment, particularly that intended for domestic use,
operates at a lower level (-10dBV) than professional equipment and will therefore
need a higher gain setting to give the same output level.
See “Initial Setup” on page 33 to learn how to set GAIN correctly.
6 Equaliser
The Equaliser (EQ) allows fine manipulation of the sound, particularly to improve
the sound in live PA applications where the original signal is often far from ideal
and where slight boosting or cutting of particular voice frequencies can really make
a difference to clarity. There are three sections giving the sort of control usually only
found on much larger mixers. The EQ knobs can have a dramatic effect, so use
them sparingly and listen carefully as you change any settings so that you get to
know how they affect the sound.
HF EQ
Turn to the right to boost high (treble) frequencies above 12kHz by up to 15dB,
adding crispness to cymbals, vocals and electronic instruments. Turn to the left to
cut by up to 15dB, reducing hiss or excessive sibilance which can occur with cer-
tain types of microphone. Set the knob in the centre-detented position when not
required.
MID EQ
There are two knobs which work together to form a SWEPT MID EQ. The lower knob
provides 15dB of boost and cut, just like the HF EQ knob, but the frequency at
which this occurs can be set by the upper knob over a range of 150Hz to 3.5kHz.
This allows some truly creative improvement of the signal in live situations, be-
cause this mid band covers the range of most vocals. Listen carefully as you use
these controls together to find how particular characteristics of a vocal signal can
be enhanced or reduced. Set the lower knob to the centre-detented position when
not required.
LF EQ
Turn to the right to boost low (bass) frequencies below 80Hz by up to 15dB, adding
warmth to vocals or extra punch to synths, guitars and drums. Turn to the left to cut
low frequencies by up to 15dB for reducing hum, stage rumble or to improve a
mushy sound. Set the knob to the centre-detented position when not required.
7 Aux Sends
These are used to set up separate mixes for FOLDBACK, EFFECTS or recording, and
the combination of each Aux Send is mixed to the respective Aux Output. For
Effects it is useful for the signal to fade up and down with the fader (this is called
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft MFX20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft MFX20 in the language / languages: English as an attachment in your email.

The manual is 2,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info