611445
14
Zoom out
Zoom in
Previous page
1/48
Next page
USER GUIDE
12
WIRING UP
Please refer to pages 35/36 for additional wiring details.
MIC INPUT
The mic input accepts XLR-type connectors and is designed to suit a wide range of BALANCED or
UNBALANCED low-level signals, whether from delicate vocals requiring the best low-noise performance or
close-miked drum kits needing maximum headroom. Professional dynamic, condenser or ribbon mics are
best because these will be LOW IMPEDANCE. While you can use low-cost HIGH IMPEDANCE mics, you do
not get the same degree of immunity to interference on the microphone cable and as a result the level of
background noise may be higher. If you turn the PHANTOM POWER on, the socket provides a suitable pow-
ering voltage for professional condenser mics.
The input level is set using the input GAIN knob.
The LINE input offers the same gain range as the MIC input, but at a higher input impedance, and is 20dB
less sensitive. This is suitable for most line level sources
LINE INPUT
Accepts 3-pole `A gauge jacks, or 2-pole mono jacks which will automatically ground the ‘cold’ input. Use
this input for sources other than mics, such as keyboards, drum machines, synths, tape machines or guitars.
The input is BALANCED for low noise and immunity from interference, but you can use UNBALANCED sourc-
es by wiring up the jacks as shown, although you should then keep cable lengths as short as possible to
minimise interference pick-up on the cable. Note that the ring must be grounded if the source is unbal-
anced. Set the input level using the GAIN knob, starting with the knob turned fully anticlockwise. Unplug
any MIC connection when using the LINE input.
INSERT POINT
The unbalanced, pre-EQ insert point is a break in the channel signal path, allowing limiters, compressors,
special EQ or other signal processing units to be added in the signal path. The Insert is a 3-pole A gauge
jack socket which is normally bypassed. When a jack is inserted, the signal path is broken, just before the
EQ section.
The signal from the channel appears on the TIP of the plug and is returned on the RING, with the sleeve as
a common ground.
The Send may be tapped off as an alternative pre-fade, pre-EQ direct output if required, using a lead with
tip and ring shorted together so that the signal path is not interrupted.
DO NOT use UNBALANCED sources with the phantom power switched on. The voltage
on pins 2 & 3 of the XLR connector may cause serious damage. BALANCED dynamic
mics may normally be used with phantom power switched on (contact your
microphone manufacturer for guidance)
WARNING ! Start with the input GAIN knob turned fully anticlockwise when plugging
high level sources into the LINE input to avoid overloading the input channel or giving
you a very loud surprise!
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft M4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft M4 in the language / languages: English as an attachment in your email.

The manual is 4,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Soundcraft M4

Soundcraft M4 User Manual - German - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info