611444
23
Zoom out
Zoom in
Previous page
1/48
Next page
USER GUIDE
21
MASTER SECTION
1
PHANTOM POWER
Many professional condenser mics need PHANTOM POWER, which is a method of sending a powering
voltage down the same wires as the mic signal. Press the switch to enable the +48V power to all of the
MIC inputs. The adjacent LED illuminates when the power is active.
WARNING: TAKE CARE when using unbalanced mics which may be damaged by the phantom
power voltage. Balanced dynamic mics can normally be used with phantom power switched
on (contact your microphone manufacturer for guidance)
Mics should always be plugged in, and all output faders set to minimum before switching
the Phantom Power ON to avoid damage to external equipment
2
POWER INDICATOR
This LED lights to show when power is connected to the console.
3
BARGRAPH METERS
The three-colour peak reading BARGRAPH METERS normally show the level of the MIX RIGHT and MIX LEFT
outputs, giving you a constant warning of excessive peaks in the signal which might cause overloading. Aim
to keep the signal just touching the red segments at peak levels for best performance.
Similarly, if the output level is too low and hardly registering at all on the meters, the level of background
noise may become significant. Take care to set up the input levels for best performance.
When any PFL switch is pressed, the meters switch to show the selected PFL signal on both meters, in
mono.
4
PLAYBACK
The rotary control sets the level of the 2 Track Tape input, which is routed to the headphones, monitor
outputs and meters. These inputs, on RCA phono connectors are an ideal way to connect the playback of a
tape machine for monitoring.
5
PLAYBACK REPLACES MIX
Press this switch to replace the MIX Left/Right signal at the MIX outputs with the Playback signal connected
to the Left and Right RCA sockets
r
(see also p.22).
6
PLAYBACK PFL
Press this switch to route the Playback signal to the monitor and phones, over-riding the default monitor/
Phones signal. This listening point is before the PB LEVEL control, so material can be previewed before being
routed.
7
MONITOR LEVEL
This control sets the level to the MONITOR LEFT & RIGHT outputs. If headphones are plugged into the
PHONES jack, the headphone level will track the Monitor Level.
8
PHONES LEVEL
This control sets the output level to the Headphone outputs. If headphones are plugged into the PHNS jack,
then the knob sets a comfortable headphone listening level without affecting the Monitor output levels.
9
AUX MASTERS
Each Aux output has a master output level control and associated AFL switch.
AUX AFLS
Just like the PFL switches on the channels, you can monitor each AUX output by pressing the AFL switch.
This routes the AUX output signal to the MONITOR or PHONES, replacing the MIX signal. The METERS also
switch from the MIX to display the PFL/AFL signal and the PFL/AFL LED lights to warn that a PFL or AFL
switch is pressed. When you release the switch, the Monitor swaps back to the MIX.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft M Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft M Series in the language / languages: English as an attachment in your email.

The manual is 4,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Soundcraft M Series

Soundcraft M Series User Manual - German - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info