611451

Soundcraft EFX Manual

24
Zoom out
Zoom in
Previous page
1/60
Next page
22
Soundcraft EFX/EPM User Guide Issue 1210
5 AUX 2 SEND (EPM only)
This is used to set up a separate mix for FOLDBACK or recording, and the
combination of each Aux Send is mixed to the Aux 2 Output. For record-
ing it is useful for the signal to fade up and down with the fader (this is
called POST-FADE), but for Foldback or Monitor feeds it is important for
the send to be independent of the fader (this is called PRE-FADE).
AUX 2 SEND is globally switchable between pre and post-fade (see
master section on page 24/25). The send pot is fed with a mono sum
of the L & R signals.
6 BALANCE
This control sets the amount of the channel signal feeding the Left and
Right MIX buses, allowing you to balance the source in the stereo image.
When the control is turned fully right or left you feed only that side of
the signal to the mix. Unity gain is provided by the control in the centre-
detented position.
7 MUTE
All outputs from the channel are enabled when the MUTE switch is released
and muted when the switch is down.
8 FADER
The 60mm FADER gives you smooth control of the overall signal level in
the channel strip, allowing precise balancing of the various source signals
being mixed to the Master Section. It is important that the input level is
set correctly to give maximum travel on the fader which should normally
be used at around the “0” mark. See the “Initial Setup” section on page
36 for help in setting the right level.
9 PFL
When the latching PFL switch is pressed, the pre-fade pre-mute signal
is fed in mono to the headphones, control room output and meters,
where it replaces the MIX. The PFL ACTIVE LED on the Master section il-
luminates to warn that a PFL is active. The Left and Right meters display
the PFL signal in mono. This is a useful way of listening to any required
input signal without interrupting the main mix, for making adjustments
or tracing problems.
10 CHANNEL PEAK LED
This LED will light when the signal level approaches clipping at any of the
three monitored points:
a) PRE-EQ
b) POST-EQ
c) POST-FADE
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft EFX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft EFX in the language / languages: English as an attachment in your email.

The manual is 3,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info